Kramer VS-44H2

Kramer Electronics Ltd.
VS-44H2 – Protocol 3000
49
Function
Description
Syntax
Parameters/Attributes
Example
FEATURE-
LIST?
Get feature state
according to the feature
ID.
COMMAND
#FEATURE-LIST?feature_id<CR>
FEEDBACK
~nn@FEATURE-LISTfeature_id,ir_state<CR><LF>
feature_id – Feature ID)
1 – Maestro
2 – Room controller
3 – Maestro panel
ir_state – IR interface
0 – disable
1 – enable
Get the room controller
feature state (for the room
controller 1):
#FEATURE-LIST?1<CR>
HDCP-MOD
Set HDCP mode.
Set HDCP working
mode on the device
input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink
- MIRROR OUTPUT.
When you define 3 as
the mode, the HDCP
status is defined
according to the
connected output in the
following priority: OUT
1, OUT 2. If the
connected display on
OUT 2 supports HDCP,
but OUT 1 does not,
then HDCP is defined
as not supported. If
OUT 1 is not
connected, then HDCP
is defined by OUT 2.
COMMAND
#HDCP-MODin_index,mode<CR>
FEEDBACK
~nn@HDCP-MODin_index,mode<CR><LF>
in_index – Number that
indicates the specific input:
1 – Input 1
2 – Input 2
3 – Input 3
4 – Input 4
mode – HDCP mode:
0 – HDCP Off
1 – HDCP On
Set the input HDCP-MODE
of Input 1 to Off:
#HDCP-MOD1,0<CR>
HDCP-MOD?
Get HDCP mode.
Set HDCP working
mode on the device
input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink
- MIRROR OUTPUT.
COMMAND
#HDCP-MOD?in_index<CR>
FEEDBACK
~nn@HDCP-MODin_index,mode<CR><LF>
in_index – Number that indicates
the specific input:
1 – Input 1
2 – Input 2
3 – Input 3
4 – Input 4
mode – HDCP mode:
0 – HDCP Off
3 – HDCP defined according to
the connected output
Get the input HDCP-MODE
of Input 1:
#HDCP-MOD?1<CR>
HDCP-
STAT?
Get HDCP signal
status.
io_mode =1 – get
the HDCP signal status
of the sink device
connected to the
specified output.
io_mode =0 – get the
HDCP signal status of
the source device
connected to the
specified input.
COMMAND
#HDCP-STAT?io_mode,in_index<CR>
FEEDBACK
~nn@HDCP-STATio_mode,in_index,status<CR><LF>
io_mode – Input/Output
0 – Input
1 – Output
in_index – Number that indicates
the specific input:
1 – Input 1
2 – Input 2
3 – Input 3
4 – Input 4
status – Signal encryption status -
valid values On/Off
0 – HDCP Off
1 – HDCP On
Get the output HDCP-
STATUS of Input 1:
#HDCP-STAT?0,1<CR>
HELP
Get command list or
help for specific
command.
COMMAND
#HELP<CR>
#HELPcmd_name<CR>
FEEDBACK
1. Multi-line:
~nn@Devicecmd_name,cmd_name…<CR><LF>
To get help for command use: HELP (COMMAND_NAME)<CR><LF>
~nn@HELPcmd_name:<CR><LF>
description<CR><LF>
USAGE:usage<CR><LF>
cmd_name – Name of a specific
command
Get the command list:
#HELP<CR>
To get help for
AV-SW-TIMEOUT:
HELPav-sw-timeout<C
R>
LOCK-FP
Lock the front panel.
In NT-52N, this
command includes the
PortNumber (1-2)
parameter.
COMMAND
#LOCK-FPlock/unlock<CR>
FEEDBACK
~nn@LOCK-FPlock/unlock<CR><LF>
lock/unlock – On/Off
0 – Off unlocks front panel buttons
1 – On locks front panel bu
Unlock front panel:
#LOCK-FP0<CR>
LOCK-FP?
Get the front panel lock
state.
In NT-52N, this
command includes the
PortNumber (1-2)
parameter.
COMMAND
#LOCK-FP?<CR>
FEEDBACK
~nn@LOCK-FPlock/unlock<CR><LF>
lock/unlock – On/Off
0 – Off unlocks front panel buttons
1 – On locks front panel buttons
Get the front panel lock
state:
#LOCK-FP?<CR>