Leica MX400 - Page 13

231 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

viii Version 3.3

Operator’s Manual Table of Contents

Table of Contents

Default Chapter2
- Product Information2
- Symbols Used in this Manual3
- Scope of this Manual4
- Related Documents4
- How to Contact Us5
- Table of Contents6
About GPS Navigation14
- Special Notes15
Functional Description17
- Receiver Configurations17
DGPS Beacon System21
Keypad & Display Description23
- Differential GPS Traffic Light Operation23
- GPS Traffic Light Operation25
- The Display26
  - The Softkeys27
- The Function Keys27
Navigate33
- N Av Function33
- Dead Reckoning34
- NAV1 - the Panorama Screen35
- NAV2 - Basic Steering Information37
- NAV 3 - Expanded Navigation Information39
- NAV4 - Sensor Input Navigation40
Route44
- RTE1 - the Active Route45
- ETA Setup60
  - SOG Based on Arrival Date & Time61
  - ETA Based on Speed61
- RTE2 - the Route Bank62
Waypoint64
- Creating and Editing Waypoints65
- Mark or Event84
- Goto O86
Plot88
- PLOT 1 - Relative to Boat90
- Man over Board99
  - Remote MOB100
Tide101
- TIDE1 - Current Tide Display101
- TIDE2 - Tide Table Port List102
- Adding a Port104
Auxiliary106
- AUX1 - Alarm Log106
- AUX2 - Speed Graph106
- AUX3 - Fuel Information106
- AUX4 - Sun Almanac106
- AUX5 - Moon Phases106
- AUX6 - Batteries106
- AUX7 -Unit Information106
Position111
- POS1 - Large Position Display111
- POS2 - Position, Altitude, Magnetic Variation, & Time113
- POS3 - Position & Log114
Gps116
- GPS1 - Current Satellite Status116
  - For 6 Channel GPS Models116
  - For 12 Channel GPS Models118
- GPS2 - GPS Health (All Models)119
Dgps123
- DGPS1 - Current DGPS Correction Status123
- DGPS3 - DGPS Messages125
Configuration126
- Alarms126
- Anchor - Anchor Watch Alarm127
- COG SOG - Course & Speed Filter Settings & Setup127
- Compass - External Compass Input & Magnetic Variation Table128
- Datum - Current Position Calculation129
- Depth - NMEA Input Control130
- DGPS - Differential Correction Input Control131
- DR - Dead Reckoning135
- Dual Contr. - Dual Station Control136
- Fuel - Fuel Input Calibration & Control136
- GPS - Elevation Mask & Antenna Offset Control138
- Init Pos - Initial Position Entry139
- Language - Foreign Language Setup140
- Lighting - Display/Keyboard Light & Contrast Control141
- Log - Speed Log Input (Pulse or NMEA 0183)142
- Log Pulses - GPS SOG Log Pulse Output144
- MX 480 - MX 480 PC Chart Interface Control144
- Navigation - Navigation Method & Waypoint Pass Criterion Control145
- NMEA out 1 Thru 4 - NMEA 0183 Output Data Control148
  - Other Special Cases Affecting NMEA 0183 Records153
- Operation - General Setup and Control Settings154
- Organizer - Automated Message Reminders156
- Position - Positioning Reference, Mode, & Alarm Control157
- Printout 2 - Printer Output Control159
- Security162
- Set & Drift162
- SJB - Smart Junction Box Control163
- Time - Mode and Format Control165
- Wind166
- Wpt & Rte Input - Uploading Waypoints into the Receiver167
Appendix A - Datum List168
Appendix B - Beacon List177
Appendix C- Engineering Mode188
- AUX7 - Unit Information & Self Test188
- Receiver Cold Start - Clearing Memory to Factory Default190
- GPS - GPS Receiver Troubleshooting191
  - GPS6 - Visible Satellite Information191
- GPS7 - GPS Position Uncertainty192
- GPS8 - Oscillator Offset Temperature Curve Fit193
- GPS9 - GPS Debug Screen194
- DGPS8 - Beacon Receiver Status196
- Beacon Signal Scope197
Appendix D - Dual Control Head Mode199
- Turning Master and Slave Units off201
Appendix E - Demonstration Mode202
Appendix F - Software Updates204
Glossary209

Related product manuals

Preview: Leica mojo 3D

Preview: Leica GPS1200 Series

Leica GPS1200 Series

Preview: Leica iNEX

Preview: Leica GS20

Preview: Leica T-Scan 5