Leica MX400 - Page 229

To Next Page

To Previous Page

Place

Stamp

Here

Leica Geosystems, Inc.

23868 Hawthorne Blvd.

Torrance, CA 90505,

USA

---------------------------------------------------------------------------------------------------

---

Main Page

Default Chapter2
- Product Information2
- Symbols Used in this Manual3
- Scope of this Manual4
- Related Documents4
- How to Contact Us5
- Table of Contents6
About GPS Navigation14
- Special Notes15
Functional Description17
- Receiver Configurations17
DGPS Beacon System21
Keypad & Display Description23
- Differential GPS Traffic Light Operation23
- GPS Traffic Light Operation25
- The Display26
  - The Softkeys27
- The Function Keys27
Navigate33
- N Av Function33
- Dead Reckoning34
- NAV1 - the Panorama Screen35
- NAV2 - Basic Steering Information37
- NAV 3 - Expanded Navigation Information39
- NAV4 - Sensor Input Navigation40
Route44
- RTE1 - the Active Route45
- ETA Setup60
  - SOG Based on Arrival Date & Time61
  - ETA Based on Speed61
- RTE2 - the Route Bank62
Waypoint64
- Creating and Editing Waypoints65
- Mark or Event84
- Goto O86
Plot88
- PLOT 1 - Relative to Boat90
- Man over Board99
  - Remote MOB100
Tide101
- TIDE1 - Current Tide Display101
- TIDE2 - Tide Table Port List102
- Adding a Port104
Auxiliary106
- AUX1 - Alarm Log106
- AUX2 - Speed Graph106
- AUX3 - Fuel Information106
- AUX4 - Sun Almanac106
- AUX5 - Moon Phases106
- AUX6 - Batteries106
- AUX7 -Unit Information106
Position111
- POS1 - Large Position Display111
- POS2 - Position, Altitude, Magnetic Variation, & Time113
- POS3 - Position & Log114
Gps116
- GPS1 - Current Satellite Status116
  - For 6 Channel GPS Models116
  - For 12 Channel GPS Models118
- GPS2 - GPS Health (All Models)119
Dgps123
- DGPS1 - Current DGPS Correction Status123
- DGPS3 - DGPS Messages125
Configuration126
- Alarms126
- Anchor - Anchor Watch Alarm127
- COG SOG - Course & Speed Filter Settings & Setup127
- Compass - External Compass Input & Magnetic Variation Table128
- Datum - Current Position Calculation129
- Depth - NMEA Input Control130
- DGPS - Differential Correction Input Control131
- DR - Dead Reckoning135
- Dual Contr. - Dual Station Control136
- Fuel - Fuel Input Calibration & Control136
- GPS - Elevation Mask & Antenna Offset Control138
- Init Pos - Initial Position Entry139
- Language - Foreign Language Setup140
- Lighting - Display/Keyboard Light & Contrast Control141
- Log - Speed Log Input (Pulse or NMEA 0183)142
- Log Pulses - GPS SOG Log Pulse Output144
- MX 480 - MX 480 PC Chart Interface Control144
- Navigation - Navigation Method & Waypoint Pass Criterion Control145
- NMEA out 1 Thru 4 - NMEA 0183 Output Data Control148
  - Other Special Cases Affecting NMEA 0183 Records153
- Operation - General Setup and Control Settings154
- Organizer - Automated Message Reminders156
- Position - Positioning Reference, Mode, & Alarm Control157
- Printout 2 - Printer Output Control159
- Security162
- Set & Drift162
- SJB - Smart Junction Box Control163
- Time - Mode and Format Control165
- Wind166
- Wpt & Rte Input - Uploading Waypoints into the Receiver167
Appendix A - Datum List168
Appendix B - Beacon List177
Appendix C- Engineering Mode188
- AUX7 - Unit Information & Self Test188
- Receiver Cold Start - Clearing Memory to Factory Default190
- GPS - GPS Receiver Troubleshooting191
  - GPS6 - Visible Satellite Information191
- GPS7 - GPS Position Uncertainty192
- GPS8 - Oscillator Offset Temperature Curve Fit193
- GPS9 - GPS Debug Screen194
- DGPS8 - Beacon Receiver Status196
- Beacon Signal Scope197
Appendix D - Dual Control Head Mode199
- Turning Master and Slave Units off201
Appendix E - Demonstration Mode202
Appendix F - Software Updates204
Glossary209

Leica MX400 - Page 229

Table of Contents

Related product manuals