LEMKEN Diamant 11 - Page 41

137 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Layout and description

39

Dural

The plough body consists of:

• Mouldboard, made up of a shin (1) and a

mouldboard (2), or slats (5).

• Share, made up of a wing (3) and a point

(4).

• Frog (6)

• Landside (7)

1

5

4

3

1

2

4

3

6

7

Table of Contents

1 General information11
- 1.1 Liability11
- 1.2 Guarantee11
- 1.3 Copyright12
- 1.4 Optional accessories12
- 1.5 Type plate13
2 Symbols used in the Operating Instructions15
- 2.1 Hazard classes15
- 2.2 Information15
- 2.3 Environmental protection15
- 2.4 Indication of passages16
3 Safety measures and precautions17
- 3.1 Target group17
- 3.2 Intended use17
- 3.3 Safety features of the device18
- 3.4 Safety and warning signs18
- 3.5 Special safety instructions21
- 3.6 Danger areas23
- 3.7 Residual risks23
  - 3.7.1 Hazard caused by mechanical systems24
  - 3.7.2 Hazard caused by hydraulic systems24
- 3.8 Applicable rules and regulations24
- 3.9 Operation on public highways24
- 3.10 Obligation of the operator31
- 3.11 Safe use of the implement32
4 Handing over the Implement35
5 Layout and description36
- 5.1 Overview36
- 5.2 Description37
6 Preparation of the Tractor44
- 6.1 Tyres44
- 6.2 Lift Rods44
- 6.3 Check Chains or Sway Blocks of the Three Point Linkage44
- 6.4 Exterior width of the tractor44
- 6.5 Control44
- 6.6 Hydraulic equipment required45
7 Preparing the implement46
- 7.1 Headstock attachment position46
- 7.2 Stand length47
- 7.3 Implement with traction increase device48
8 Attaching the implement49
- 8.1 General49
- 8.2 Procedure51
9 Uncoupling the implement54
- 9.1 Set the length of the lifting rods54
- 9.2 Work instruction55
10 Driving on public highways59
- 10.1 General information59
- 10.2 Preparation for driving on public roads59
- 10.3 Transport61
  - 10.3.1 Permissible transport height61
  - 10.3.2 Permissible transport speed61
- 10.4 Lighting equipment and identification62
11 Operation66
- 11.1 Rotating the frame66
  - 11.2.1 General67
  - 11.2.2 Converting from F operation to O operation68
  - 11.2.3 Converting from O operation to F operation69
- 11.3 Turning on the headland71
- 11.4 Damper on land wheel72
- 12.1 Front furrow width74
- 12.2 Distance from the tractor to the edge of the furrow (online version only)75
- 12.3 Working depth76
- 12.4 Tilt77
- 12.5 Working width per body (Diamant)78
- 12.6 Working width for each body (Diamant V)79
- 12.7 Side pull80
- 12.8 Draw point height (only in on-land configuration)81
- 12.9 Pitch angle82
  - 12.9.1 DuraMaxx plough body82
  - 12.9.2 DURAL plough body84
- 12.10 Landside86
- 12.11 Sword coulter87
- 12.12 Trashboard88
- 12.13 Subsoilers91
- 12.14 Wide furrow cutter92
- 12.15 Skimmers92
  - 12.15.1 General information92
  - 12.15.2 Working depth93
  - 12.15.3 Turning forwards or backwards94
  - 12.15.4 Projection angle adjustment95
- 12.16 Disc coulters96
  - 12.16.1 General information96
  - 12.16.2 Working depth97
  - 12.16.3 Side distance98
  - 12.16.4 Swivel restriction99
- 12.17 Land wheel101
  - 12.17.1 General101
  - 12.17.2 Setting the return spring102
12 ADJUSTMENTS73
13 Overload safety devices103
- 13.1 Shearing protection103
- 13.2 Hydromatic hydraulic overload safety device105
14 Attachment arm118
15 Put the implement out of operation119
- 15.1 Shutting down the implement in an emergency119
- 15.2 Disposal119
16 Maintenance and repairs120
- 16.1 Special safety instructions120
- 16.2 Environmental protection123
- 16.3 Maintenance intervals123
- 16.4 Tightening torques124
- 16.5 Check the connections to the tractor126
  - 16.5.1 Hydraulic connections126
  - 16.5.2 Electrical connections126
- 16.6 System pressure of the traction increase device127
  - 16.6.1 Reading the system pressure127
  - 16.6.2 Changing the system pressure128
- 16.7 Air pressure of the tyres129
- 16.8 Lubrication chart130
17 Troubleshooting132
- 17.1 Plough insertion and guidance, slip132
- 17.2 Miscellaneous132
18 Technical data133
- 18.1 List of models with shearbolt device133
- 18.2 List of models with Hydromatic overload protection133
- 18.3 Permissible output range134
- 18.4 Weights134
19 Noise, Airborne Sound135
20 Notes135
Index136

Related product manuals

Preview: LEMKEN Solitair DT/400

LEMKEN Solitair DT/400

Preview: LEMKEN RUBIN 10

LEMKEN RUBIN 10

Preview: LEMKEN Zirkon 10

LEMKEN Zirkon 10

Preview: LEMKEN Solitair 9

LEMKEN Solitair 9

Preview: LEMKEN Opal 090 B

LEMKEN Opal 090 B

Preview: LEMKEN Heliodor 9 K

LEMKEN Heliodor 9 K

LEMKEN EuroLux 800 TL

LEMKEN EuroLux 1000 TLE