LEMKEN Diamant 11 - On-land Ploughing (OF)

137 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Driving on public highways

63

10.4.3 Identifications

− Depending on country specific require-

ments, attach identifications, e.g. regis-

tration plates, SMV triangle or other re-

flectors, and connect them using the

plug (10).

• Variant 1

• Variant 2

10

Table of Contents

1 General information11
- 1.1 Liability11
- 1.2 Guarantee11
- 1.3 Copyright12
- 1.4 Optional accessories12
- 1.5 Type plate13
2 Symbols used in the Operating Instructions15
- 2.1 Hazard classes15
- 2.2 Information15
- 2.3 Environmental protection15
- 2.4 Indication of passages16
3 Safety measures and precautions17
- 3.1 Target group17
- 3.2 Intended use17
- 3.3 Safety features of the device18
- 3.4 Safety and warning signs18
- 3.5 Special safety instructions21
- 3.6 Danger areas23
- 3.7 Residual risks23
  - 3.7.1 Hazard caused by mechanical systems24
  - 3.7.2 Hazard caused by hydraulic systems24
- 3.8 Applicable rules and regulations24
- 3.9 Operation on public highways24
- 3.10 Obligation of the operator31
- 3.11 Safe use of the implement32
4 Handing over the Implement35
5 Layout and description36
- 5.1 Overview36
- 5.2 Description37
6 Preparation of the Tractor44
- 6.1 Tyres44
- 6.2 Lift Rods44
- 6.3 Check Chains or Sway Blocks of the Three Point Linkage44
- 6.4 Exterior width of the tractor44
- 6.5 Control44
- 6.6 Hydraulic equipment required45
7 Preparing the implement46
- 7.1 Headstock attachment position46
- 7.2 Stand length47
- 7.3 Implement with traction increase device48
8 Attaching the implement49
- 8.1 General49
- 8.2 Procedure51
9 Uncoupling the implement54
- 9.1 Set the length of the lifting rods54
- 9.2 Work instruction55
10 Driving on public highways59
- 10.1 General information59
- 10.2 Preparation for driving on public roads59
- 10.3 Transport61
  - 10.3.1 Permissible transport height61
  - 10.3.2 Permissible transport speed61
- 10.4 Lighting equipment and identification62
11 Operation66
- 11.1 Rotating the frame66
  - 11.2.1 General67
  - 11.2.2 Converting from F operation to O operation68
  - 11.2.3 Converting from O operation to F operation69
- 11.3 Turning on the headland71
- 11.4 Damper on land wheel72
- 12.1 Front furrow width74
- 12.2 Distance from the tractor to the edge of the furrow (online version only)75
- 12.3 Working depth76
- 12.4 Tilt77
- 12.5 Working width per body (Diamant)78
- 12.6 Working width for each body (Diamant V)79
- 12.7 Side pull80
- 12.8 Draw point height (only in on-land configuration)81
- 12.9 Pitch angle82
  - 12.9.1 DuraMaxx plough body82
  - 12.9.2 DURAL plough body84
- 12.10 Landside86
- 12.11 Sword coulter87
- 12.12 Trashboard88
- 12.13 Subsoilers91
- 12.14 Wide furrow cutter92
- 12.15 Skimmers92
  - 12.15.1 General information92
  - 12.15.2 Working depth93
  - 12.15.3 Turning forwards or backwards94
  - 12.15.4 Projection angle adjustment95
- 12.16 Disc coulters96
  - 12.16.1 General information96
  - 12.16.2 Working depth97
  - 12.16.3 Side distance98
  - 12.16.4 Swivel restriction99
- 12.17 Land wheel101
  - 12.17.1 General101
  - 12.17.2 Setting the return spring102
12 ADJUSTMENTS73
13 Overload safety devices103
- 13.1 Shearing protection103
- 13.2 Hydromatic hydraulic overload safety device105
14 Attachment arm118
15 Put the implement out of operation119
- 15.1 Shutting down the implement in an emergency119
- 15.2 Disposal119
16 Maintenance and repairs120
- 16.1 Special safety instructions120
- 16.2 Environmental protection123
- 16.3 Maintenance intervals123
- 16.4 Tightening torques124
- 16.5 Check the connections to the tractor126
  - 16.5.1 Hydraulic connections126
  - 16.5.2 Electrical connections126
- 16.6 System pressure of the traction increase device127
  - 16.6.1 Reading the system pressure127
  - 16.6.2 Changing the system pressure128
- 16.7 Air pressure of the tyres129
- 16.8 Lubrication chart130
17 Troubleshooting132
- 17.1 Plough insertion and guidance, slip132
- 17.2 Miscellaneous132
18 Technical data133
- 18.1 List of models with shearbolt device133
- 18.2 List of models with Hydromatic overload protection133
- 18.3 Permissible output range134
- 18.4 Weights134
19 Noise, Airborne Sound135
20 Notes135
Index136

Related product manuals

Preview: LEMKEN Solitair DT/400

LEMKEN Solitair DT/400

Preview: LEMKEN RUBIN 10

LEMKEN RUBIN 10

Preview: LEMKEN Zirkon 10

LEMKEN Zirkon 10

Preview: LEMKEN Solitair 9

LEMKEN Solitair 9

Preview: LEMKEN Opal 090 B

LEMKEN Opal 090 B

Preview: LEMKEN Heliodor 9 K

LEMKEN Heliodor 9 K

LEMKEN EuroLux 800 TL

LEMKEN EuroLux 1000 TLE