What to do if Lenovo ThinkServer RD240 stops responding during hard disk drive diagnostic test?
If the server stops responding during the hard disk drive diagnostic test, remove the hard disk drive that was being tested and run the diagnostic test again. If the test runs successfully, replace the removed drive with a new one.
Why is the mouse or pointing device not working on my Lenovo ThinkServer RD240 Server?
If your Lenovo Server's mouse or pointing device isn't working, ensure it's compatible with the server by checking the Lenovo website. Verify the device cable is securely connected, the correct drivers are installed, and the server and monitor are on. If using a USB device connected to a hub, connect it directly to the server. Also, ensure the mouse is enabled in the Setup Utility program. If these steps don't resolve the issue, replace the mouse or pointing device.
What to do if not all drives are recognized by the hard disk drive diagnostic tests on Lenovo ThinkServer RD240 Server?
If not all drives are recognized by the hard disk drive diagnostic tests on your Lenovo Server, remove the drive indicated by the tests, and then run the tests again. If the remaining drives are recognized, replace the removed drive with a new one.
How to fix if the DVD drive is not recognized on Lenovo ThinkServer RD240?
If the DVD drive is not recognized on your Lenovo Server, ensure that the SATA channel to which the DVD drive is attached is enabled in the Setup Utility program. Also, check that all cables and jumpers are installed correctly, the signal cable and connector are not damaged, and the correct device driver is installed for the DVD drive. Reseat the DVD drive and its cables. If the issue persists, replace the DVD drive and cables.
What to do if a hard disk drive was not detected while the operating system was being started on Lenovo ThinkServer RD240?
If a hard disk drive was not detected while starting the operating system on your Lenovo Server, try reseating all hard disk drives and cables. Then, run the hard disk drive diagnostic tests again.
How to fix Lenovo Server power-control button if it does not work?
If the power-control button on your Lenovo Server isn't working and the server won't start, try the following: 1. Disconnect and reconnect the server power cords. If you are a trained service technician, reseat the operator information panel cables, and repeat the power cord steps. If the server starts, reseat the operator information panel; if the problem persists, replace it. 2. Ensure the power cords are correctly connected to the server and a working outlet, the correct memory type is installed and fully seated, the power supply LEDs don't indicate a problem, and the microprocessors are installed correctly. 3. Reseat the DIMMs, and (if you are a trained service technician) the power switch connector and power backplane. 4. Replace the DIMMs, and (if you are a trained service techn...
What to do if Lenovo ThinkServer RD240 Server stops responding during hard drive diagnostic test?
If the Lenovo Server stops responding during the hard disk drive diagnostic test, remove the hard disk drive that was being tested when the server stopped responding, and run the diagnostic test again. If the test runs successfully, replace the removed drive with a new one.
What to do if multiple rows of DIMMs are failing on Lenovo ThinkServer RD240 Server?
If multiple rows of DIMMs in a branch are identified as failing on your Lenovo Server: 1. Reseat the DIMMs, then restart the server. 2. Replace the lowest-numbered DIMMs with identical, known good DIMMs, then restart the server. Repeat as necessary.
Why is the Lenovo ThinkServer RD240 optional device that was just installed not working?
If a Lenovo optional device that was just installed isn't working, ensure that the device is designed for the server and that you followed the installation instructions correctly, without loosening any other devices or cables. Also, update the configuration information in the Setup Utility program. Reseat the newly installed device, and if the issue continues, replace it.
How to fix Lenovo Server DVD drive if it is not recognized?
If the Lenovo Server DVD drive is not recognized: 1. Ensure that the SATA channel to which the DVD drive is attached is enabled in the Setup Utility program, all cables and jumpers are correctly installed, the signal cable and connector are not damaged, and the correct device driver is installed for the DVD drive. 2. Reseat the DVD drive and its cables. 3. Replace the DVD drive, then the DVD drive cables, and finally (if you are a trained service technician) the system board, one at a time, restarting the server each time.
A roadmap outlining tasks for server setup and their corresponding locations in the manual.
Provides essential guidelines for safe and proper server installation and component handling.
General section for installing or removing optional hardware devices.
Instructions for installing or removing memory modules.
Final steps to complete parts replacement and prepare the server.
Using the server's firmware utility to view and change system configuration settings.
Configuring the onboard LSI SAS RAID controller.
Configuring the ThinkServer 8708ELP SAS RAID controller.
Using the EasyStartup DVD to simplify RAID and OS installation.
Viewing and changing RAID settings for supported controllers.
Guidance on installing the operating system, including typical Windows setup.
Tables providing solutions for identifiable server symptoms.
Troubleshooting steps for DVD drive recognition and functionality problems.
Troubleshooting steps for hard disk drive recognition and operational problems.
Resolving problems related to system memory display and configuration.
Addressing issues indicated by server beeps during POST.
Troubleshooting steps for power-related problems, including server start-up failures.
Resolving problems with Ethernet controller connectivity.
Steps to diagnose and resolve problems not covered by other sections.
Procedures and information required when calling the Lenovo support center.
General| Form Factor | 2U Rack |
|---|---|
| Processor Sockets | 2 |
| Chipset | Intel 5520 |
| Processor | Intel Xeon 5600 series |
| Storage | Up to 8 hot-swap 2.5" or 3.5" drives |
| RAID Support | RAID 0, 1, 10, 5 |
| Networking | 2 x 1Gb Ethernet ports |
| Operating System Support | Windows Server, Red Hat Enterprise Linux, SUSE Linux Enterprise Server, VMware ESXi |
| Memory Slots | 12 DIMM slots |
To Next Page