Lenze 9300 vector - Page 460

Appendix
Index
14
14.2

14.2−3
EDSVF9383V EN 6.0−11/2009
Display
− Application datum, 9.1−1
− operating status, 9.2−1
Display functions, 9.1−1
− Possible values, 9.1−1
Display of operating data, 9.1−1
Display values, 9.1−1
− Calibration, 9.1−1
Disposal, 2.1−3
Distributed supply, 10.6−1
Drive behaviour
− Controller inhibit, 6.4−1
− in the event of faults, 9.3−1
Drive errors, 9.4−1
E
Earth fault in motor cable (OC2), 8.3−3
Electrical installation, system bus (CAN), 5.6−1
EMC, what to do in case of interferences, 5.2−6
Emergency−off, Controller inhibit, 6.4−1
EMZ9371BC keypad, changing parameters, 7.2−7 , 7.2−8
Entry of motor data, 6.6−1
Error analysis, Via history buffer, 9.2−1
Error messages, 9.5−1
− causes and remedies, 9.5−1
− configuration, 8.4−1
− General, 9.5−1
− Resetting, 9.5−5
Exceeding of the maximum speed (NMAX), 8.3−3
Explanations, Code table, 8.5−1
External brake resistors, 12.2−1
External error (EEr), 8.3−7
F
Failure of a motor phase, 8.3−4
Fan connection EVx9335 ... EVx9383
− Controller is supplied via the DC bus, 5.3−6 , 5.4−10
− controller is supplied with mains voltage, 5.3−5 , 5.4−10
Fault analysis, Via history buffer, 9.2−1
Fault elimination, 9.4−1
Fault messages
− causes and remedies, 9.5−1
− OC3 in clamp operation, 9.4−2
Fault responses, 8.3−1
Feedback system, wiring, 5.7−1
Field controller, 6.8−8 , 8.5−8
Field frequency
− maximum, 6.10−1
− Minimum, 6.10−1
Free mounting spaces, 4.1−1
Free spaces, 3.1−2
Function blocks, 8.2−1
− diameter calculator (DCALC1), 8.2−1
− internal motor control, vector control (MCTRL2), 8.2−40
− master frequency input (DFIN), 8.2−5
− master frequency output (DFOUT), 8.2−8
− master frequency processing (DFSET), 8.2−18
− master frequency ramp−function generator
(DFRFG1), 8.2−13
Functional test, safety function, 11.4−2 , 11.4−5
G
gases, aggressive, 4.1−1
General accessories, 13.1−1
General data, 3.1−1 , 7.2−1
H
Heatsink temperature, monitoring, 8.3−6
History buffer, 9.2−1
− Assembly, 9.2−2
− clear, 9.2−2
I
Imax limit in generator mode, in generator mode, 6.6−15 ,
8.2−27 , 8.2−42 , 8.5−4
Imax limit in motor mode, 6.6−15 , 8.2−27 , 8.2−42 , 8.5−4
Incremental encoder
− At X8, 5.7−2 , 6.7−2
− at X9, 5.7−3 , 6.7−3
− operation with, 8.2−48
− with HTL level, 5.7−3 , 6.7−3
− With TTL level, 5.7−2 , 6.7−2
Input signals
− Analog, Configuration, 6.5−4
− Digital, Configuration, 6.5−1
Inputs
− Digital, Response times, 6.5−1
− KTY, 6.6−11
− PTC, 6.6−9
Interaction with compensation equipment, 5.1−4
efesotomasyon.com - Lenze