What to do if Lippert Components ground control TT shows 'EXCESS ANGLE'?
If your Lippert Components Lifting Systems displays an 'EXCESS ANGLE' error, the cause may be an unsecured controller or an uneven or sloped site. To resolve this, check and secure the controller placement. If the issue continues, relocate the trailer.
What to do if my Lippert Components ground control TT shows 'EXCESSIVE ANGLE'?
If your Lippert Components Lifting Systems displays an 'EXCESSIVE ANGLE' error, it means that excessive angle was reached during manual operation. Stop manual operation and reset jacks to a more level state. The code will self-clear, so there is no need to hit “OK.”
What to do if Lippert Components ground control TT Lifting Systems shows 'OUT OF STROKE'?
If your Lippert Components Lifting Systems displays an 'OUT OF STROKE' error, it may be caused by an unsecured controller or an uneven or sloped site. Check and secure the controller placement. If the problem persists, relocate the trailer.
Why does my Lippert Components Automobile Accessories touch panel say “LOW VOLTAGE”?
The “LOW VOLTAGE” message on your Lippert Components Automobile Accessories touch panel indicates a potential issue with the power supply. This could be due to a bad connection or wiring, requiring you to check, repair, or replace the wiring. Alternatively, it could be caused by a discharged or bad battery, in which case you should test the battery voltage under load and either charge or replace the battery.
What to do if my Lippert Components ground control TT Lifting Systems shows 'AUTO LEVEL FAILURE'?
If your Lippert Components Lifting Systems displays an 'AUTO LEVEL FAILURE' error, it could be due to an unsecured controller or a voltage drop. To resolve this, check and secure the controller placement. Additionally, test the battery voltage under load and charge or replace the battery if necessary.
What to do if Lippert Components Lifting Systems shows 'LOW VOLTAGE'?
If your Lippert Components Lifting Systems displays a 'LOW VOLTAGE' error, the cause may be a bad connection or wiring, or a discharged or bad battery. You should check the wiring, repairing or replacing as necessary. Also, test the battery voltage under load and either charge or replace the battery if needed.
What to do if my Lippert Components Automobile Accessories touch panel says “FUNCTION ABORTED”?
The “FUNCTION ABORTED” message on your Lippert Components Automobile Accessories touch panel indicates that the user has aborted an automatic leveling sequence. Restart the sequence.
What to do for the “EXCESSIVE ANGLE” message on my Lippert Components Automobile Accessories touch panel?
If your Lippert Components Automobile Accessories touch panel displays the “EXCESSIVE ANGLE” message, stop the manual operation and reset the jacks to a more level state. The code will self-clear.
What does “BAD CALIBRATION” mean on my Lippert Components Automobile Accessories touch panel?
The “BAD CALIBRATION” message on your Lippert Components Automobile Accessories touch panel indicates that the trailer zero point was not set correctly. Reset the zero point.
What does “EXTERNAL SENSOR” mean on my Lippert Components Automobile Accessories touch panel?
The “EXTERNAL SENSOR” message on your Lippert Components Automobile Accessories touch panel indicates a bad connection or wiring issue with the rear remote sensor. Replace or repair the connection to the rear remote sensor.
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
Detailed instructions for mounting the system's brackets and jacks.
Guides the installation of front spacer kits and C-jacks onto the trailer frame.
Guides the installation of rear mounting brackets and 5K short jacks.
Procedure for installing the primary power tongue jack.
Instructions for locating and mounting the leveling sensors for optimal performance.
Steps for installing the main system controller.
Detailed steps for the automatic leveling sequence of the trailer.
Guides to interpreting LED status and handling system error displays.
Troubleshooting specific error messages shown on the OneControl touch panel.
Steps to clear special jack error codes by homing the jacks.
Procedure to set the system's zero point for accurate auto leveling.
Schematic illustrating the electrical connections of the leveling system components.
General| Brand | Lippert Components |
|---|---|
| Model | ground control TT |
| Category | Lifting Systems |
| Language | English |
To Next Page
