To Next PageTo Next PageWhat to do if Mellanox Technologies IS5030Q-2SFC Switch is not working and unresponsive?
Try resetting the switch. If that doesn't work, unplug the switch, wait 5 minutes, and then plug it back in. If the switch still doesn't come on, check the power supplies. If it does come on, use the FabricIT management CLI or Web GUI to find out the cause of the shutdown.
How to turn on Mellanox Technologies IS5030Q-2SFC if it is off?
Try these steps: unplug the switch, wait 5 minutes, then plug it back in. If the switch doesn't turn on, check the power supplies. If it does turn on, use the FabricIT management CLI or Web GUI to determine the cause of the shutdown. Also, check the temperature and fan status.
Why does the power LED for Mellanox Technologies Switch shut off?
Check that there is adequate ventilation and that the fan LEDs indicate that the fans are running. Make sure nothing is blocking the front or rear of the chassis and that the fan modules and ventilation holes are not blocked, especially by dust. If dust is present, clean the fan unit and remove dust from the front and rear panels of the switch using a vacuum cleaner.
What to do if the last software update did not succeed on Mellanox Technologies IS5030Q-2SFC?
Connect the RS232 connector (CONSOLE) to a laptop. Then, push the reset button on the switch or management module. You will have approximately 5 seconds to stop the U-Boot by pressing Control-B.
General| Brand | Mellanox Technologies |
|---|---|
| Model | IS5030Q-2SFC |
| Category | Switch |
| Language | English |
Identifies serial number and GUID for switch models.
Location of serial number and GUID on externally managed switches.
Location of serial number, GUID, and MAC for internally managed switches.
Details the location of the license key for FabricIT on the pull-out tab.
Describes the front and rear views of the switch, ports, and modules.
Details system status indicators on the connector and power side panels.
Explains the meaning of system status LED configurations (Green, Yellow, Red, Off).
Describes the system health LED on the power side panel.
Explains port status based on LED indications for physical and logical links.
Details status indicators for Power Supply Units (PSUs).
Explains the status indications for the fan module.
Describes the function and operation of the reset button.
Discusses the two possible air flow patterns for the switch.
Specifies the power budget classification for QSFP cables.
Overview of the different interfaces available for connecting to the switch.
Describes the 36 QSFP ports on the connector side panel.
Details the layout and orientation of the 36 QSFP ports.
Illustrates the orientation of ports on the top and bottom rows.
Lists the interfaces for management and firmware updates (MGT, USB, CONSOLE).
Describes the CONSOLE port for initial host PC connection.
Details the I2C connector for debug and troubleshooting on unmanaged switches.
Explains the MGT port for remote management connections.
Describes the USB connector for software and firmware updates.
Details the I2C interface for debug and troubleshooting.
Lists the items included in the switch package.
Introduces the installation and initialization process for the switch platform.
Provides critical safety warnings for equipment installation.
Details the procedure for physically installing the switch into a rack.
Specifies rack depth requirements for different rail kits and switch sizes.
Outlines the steps for installing the switch using rack rail kits.
Explains the importance and procedure for grounding the switch.
Guides on connecting power and performing the initial power-on sequence.
Provides instructions for removing and installing power supply units (PSUs).
Details how to install and remove InfiniBand cables.
Guides on removing and installing the fan module.
Steps for removing the switch from its rack mounting.
Information on proper disposal of the equipment.
Information on Mellanox OpenFabric software for network management.
Describes the features of the internally managed switch system.
Details the features of subnet management within the switch.
Explains Mellanox Unified Fabric Manager (UFM) capabilities.
Steps for initial configuration of the switch via the CONSOLE port.
Methods for establishing remote connections (SSH, Telnet, WEB).
How to access the switch CPU using the Ethernet connector.
Instructions on obtaining and downloading new firmware versions.
Specifics for unmanaged switches, including interface differences.
Details the I2C connector's use for debug and troubleshooting.
Commands to check the currently installed firmware version.
Steps for updating firmware via the InfiniBand network.
Procedure for reprogramming firmware using the I2C port.
Detailed steps for reprogramming via the I2C port using MTUSB-1.
Information on downloading Mellanox Firmware Tools and their documentation.
Instructions for downloading and using the OpenSM subnet manager.
Troubleshooting steps for power supply unit related issues.
Troubleshooting for the switch power LED being off.
Troubleshooting for the fan status LED not illuminating.
Troubleshooting for InfiniBand link LEDs not functioning.
Troubleshooting for the activity LED not lighting up.
Steps to diagnose and resolve when the switch is completely off.
Steps for when the switch is unresponsive.
Troubleshooting steps if a firmware update fails.
Detailed specifications for the IS5025 switch model.
Detailed specifications for the IS5030 switch model.
Detailed specifications for the IS5035 switch model.
Information on EMC certifications for the switch.
General EMC statements applicable to the switch.
FCC compliance statements for US operations.
European compliance statements (EN55022).
Canadian compliance statements (ICES-003).
Warning statements related to China CCC certification.
VCCI compliance statements for Japan.
MIC certification details for Korean operations.
Lists tools and parts required for passing the power cord.
Details the components included in the rack installation kit.
Step-by-step instructions for routing power cords in a rack.
Pinout details for the InfiniBand QSFP connector.
Pinout and wiring color coding for the RJ45 CONSOLE interface.
Table listing part descriptions and their corresponding ordering numbers (OPN).
