mensor PCS 400 - INTRODUCTION

118 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

U

ser

'

s

N

otes:

TABLE OF CONTENTS PCS 400

xii www.mensor.com

Table of Contents

Default Chapter3
- Warranty3
- Warnings and Caution Notes4
- Important Note4
- Packaging for Shipment5
- FCC Radio Frequency Emission Notice5
- Trademarks5
- Mensor Background6
- Summary of Contents7
- Table of Contents8
Introduction14
- Meet Your Model PCS 40014
- Summary of PCS 400 Functions18
- Accreditations19
- Calibration Services19
- Mensor Service Plus19
- PCS 400 Evolution19
- Power up19
- DID You Get Everything14
- Initial Inspection14
Installation20
- Mounting20
- Pressure Connections20
- Power on21
- System Checkout21
  - Control Pressure Check21
  - System Leak Check21
- Display24
- Keypad24
Local Operation24
- Default Values30
- Transducer30
- MEASURE Mode31
  - Autorange31
- Control Modes32
- Optional Control Modes33
- Manual Valves Test34
- Sequences34
- Solenoid Valves Test34
- Ieee-488-Std (Gpib)42
Remote Operation42
- Device Dependent Messages42
- PCS 400 Command Responses48
- Serial Communication57
  - Cable Requirements57
  - Setup57
- Beyond the Warranty60
- Electrical Module60
Maintenance60
- Module Replacement60
- Program Disk Replacement60
- Troubleshooting Guide61
  - Error Symptoms and Solutions62
  - Table 5.1 - Error Symptoms and Solutions62
- Spare Parts List65
- Table 5.2 - Spare Parts65
Calibration66
- Calibration Environment66
- Calibration Medium66
- Calibration Procedures66
- Pressure Standard66
- Calibrating a Gauge Pressure Instrument67
- Calibrating an Absolute Pressure Instrument68
- Control Specifications70
- Measure Specifications70
Specifications70
- General Specifications71
- Figure 7.1 - Dimensional Outline72
1 Rack Mount Kit75
- Figure 8.1 - Rack Mount Dimensions75
- Figure 8.2 - Rack Specifications76
- Figure 8.3 - Slide Specifications76
2 Transport Case77
- Figure 8.4 - Transport Case77
3 Multiple Range Pneumatics Kit78
- 3A - Barometric Reference Transducer78
- 3B - Two Independent Internal Transducers78
4 High Pressure Control Unit80
5 Ti/Heise/Mensor Model 179 Controller Emulation80
6 Vacuum Gauge and Tube80
- Figure 8.5 - High Pressure Control Unit80
- Figure 8.7 - VT-6 Gauge Tube Wiring81
7 Bi-Directional Pressure Control82
8 Pressure Emulation Modes82
- 8A - Gauge Transducers (Absolute Emulation) Without BRT83
- 8B - Gauge Transducers (Absolute and Vacuum Emulation) with BRT83
- Table 8.1 - Effects of Mode Switching (Gauge Transducer)83
- Table 8.2 - Effects of Mode Switching (Absolute Transducer)83
- 8C - Absolute Transducers (Gauge Emulation) with BRT84
9 External Analog Input84
10 Large Volume85
- Figure 8.8 - Large Volume Option (<1000 CC's External)86
- Figure 8.9 - Large Volume Option (>1000 CC's External)86
11 BCD Output87
- Figure 8.10 - BCD Output/Analog Input Connector88
12 Two's Complement Binary Output89
- Table 8.3 - Characters for Display Resolution89
13 Servo-Disable91
14 External Measure Mode Switch91
15 Measure Mode Signal91
16 Low Pressure External Plumbing92
Appendix94
- Table 9.1 - Measurement Units (Unitno)94
- Conversion Factors, PSI (Table 9.2)95
- Table 9.2 - Conversion Factors, PSI95
- Table 9.3 - Conversion Factors, Pascal96
- Temperature Conversion (Table 9.4)97
- Table 9.4 - Temperature Conversion Chart97
- Solenoid Valve Truth Table (Table 9.5)98
- Table 9.5 - Solenoid Valve Truth Table98
- Head Pressure Correction99
- Gas Density (Table 9.6)99
- Liquid Density (Table 9.7)99
- Table 9.6 - Gas Density99
- Table 9.7 - Liquid Density99
- Head Pressure Calculation (Figure 9.1)100
- Sample Program101
- Common Remote Commands Quick Reference (Table 9.8)103
- PCS 400 Sequence Program Script109
Index110