To Next Page
C
Cynthia DiazSep 12, 2025
What does error #7000 mean on MHM Industrial Equipment?
- SslewisSep 12, 2025
Error #7000 indicates that there is wrong firmware on master PCB.
What does error #7000 mean on MHM Industrial Equipment?
Error #7000 indicates that there is wrong firmware on master PCB.
What does error #7001 mean on MHM SYNCHROPRINT 5000 Industrial Equipment?
Error #7001 indicates that the update is not possible because of wrong hardware.
What does error #7002 mean on MHM SYNCHROPRINT 5000?
Error #7002 indicates that there is a wrong software version on the PCB.
What does error #7003 mean on MHM SYNCHROPRINT 5000 Industrial Equipment?
Error #7003 indicates different software versions on the PCBs.
What to do if control panel of MHM Industrial Equipment does not boot up?
If the control panel doesn't boot up, there could be several reasons: * The main power switch might be off. If so, switch it on. * There might be no power supply to the machine. Check if the frequency converter display is active. If not, reestablish the power supply. * There might be no 24V power supply at the control panel. Check if the station displays are on. If not, a fuse or the ON/OFF relay could be defective. * The terminal unit might not be connected to the Servo- PCB. In this case, check the wiring from the terminal unit to the Servo-PCB panel.
What does error #4001 mean on MHM Industrial Equipment?
Error #4001 indicates that the lift up sensor signal is missing. Check the adjusting, wiring and function of the sensor.
What does error #4002 mean on MHM Industrial Equipment?
Error #4002 indicates that the lift down sensor signal is missing. Check the adjustment, wiring, and function of the sensor.
What does error #4003 mean on MHM Industrial Equipment?
Error #4003 indicates that the starting lockout is active and indexing is not possible. Check the input signal.
What does error #4004 mean on MHM SYNCHROPRINT 5000?
Error #4004 means that the off contact position signal is out of range. Check the Master- PCB parameters and wiring.
What does error #4005 mean on MHM SYNCHROPRINT 5000?
Error #4005 indicates that the off contact target has not been reached. Check the mechanics, wiring, and Master-PCB setting.
Provides guidance on using the operating instructions and notes on potential specification changes.
Explains the meaning of keywords and symbols used to denote dangers and important information.
Covers general safety regulations and the need for skilled staff for operation and maintenance.
Defines qualified personnel and lists responsibilities for safe operation and maintenance.
Details the specific skills and qualifications needed for various operating and maintenance tasks.
Outlines critical safety rules for operators, including keeping cabinets closed and using safety devices.
Specifies the required personal protective equipment for operators during work.
Identifies potential risks such as electrical, mechanical, and substance-related hazards.
Lists safety signs attached to the machine and their meanings and locations.
Reminds the customer to comply with all applicable regulations in the machine's operating country.
Explains how to use the EMERGENCY STOP button and safety bars to halt the machine.
Describes how the machine automatically stops the main drive upon detecting malfunctions.
Details the procedure for starting the machine, including checks and reference position initialization.
Introduces the MHM Hybrid-Control system and the control panels at print stations.
Explains controlling the machine via tablet or terminal and switching between them.
Guides on using the tablet PC for controlling main operating features through touch commands.
Explains using the "Adjust" menu on the tablet to configure the machine for the print job.
Describes operating the machine in manual mode, processing one index and working cycle at a time.
Details automatic mode where index and working cycles start continuously for production.
Covers elementary adjustments for machine setup, cleaning, and alignment via the BasicSetup menu.
Explains how the "Help" function supports troubleshooting and machine control.
Describes how operation can be automatically blocked and how to eliminate the blocking reason.
Explains operation using the fixed function keys and adjustable knobs on the terminal.
Details the "Adjust" function on the terminal for machine setup, including displays for direction and speed.
Describes operating in manual mode via the terminal, processing one index and working cycle.
Explains automatic mode via the terminal, where cycles start continuously after an index.
Covers error messages displayed on the terminal and tablet, including error codes and descriptions.
Details error messages displayed in red on the terminal with error number and text.
Explains error messages shown on the tablet, including error description and confirmation steps.
Indicates that the serial number and year of manufacture are found on the machine's type plate.
Presents diagrams showing the dimensions of various Synchroprint models.
Provides detailed technical specifications for different Synchroprint models in a table format.
Covers general safety notes for transportation, including falling objects and proper lifting procedures.
Describes that the Synchroprint is packed in wooden crates and provides information on variations.
Details the customer's responsibility for unloading and the required equipment, warning of mechanical damage.
States that installation must be performed by MHM service technicians to avoid warranty cancellation.
Guides on mounting the machine on a load-bearing bed and maintaining adequate distance from surroundings.
Specifies optimal ambient conditions like temperature, humidity, and air quality for machine operation.
Locates connections for compressed air and mains electricity on the base unit.
Details the electrical requirements, including supply voltage, frequency, and connected load.
Outlines the necessary compressed air specifications, including type of machine, consumption, and pressure.
Explains the step-by-step printing process from substrate application to unloading.
Identifies key components of the Synchroprint machine with labels on an image.
Provides an overview of the main control panel, including buttons like EMERGENCY STOP and tablet interface.
Lists and describes the machine's safety devices, such as EMERGENCY STOP buttons and safety bars.
Details the types of pallets used, their dimensions, and the maximum allowed weight.
Explains the function of the foot switch for starting index movements in manual mode.
Indicates the location of the type plate containing machine identification details.
Describes the main power switch's location and function for immediate disconnection from power.
Introduces print stations used for printing individual colors and mentions manual/automatic versions.
Shows a labeled diagram of the components of a manual print station.
Details individual parts of the manual print station, including the squeegee arm motor and dryer connector.
Explains how to adjust screen positioning using hand wheels for precise alignment.
Describes adjusting the squeegee carriage travel for reduced printing times and increased production.
Explains how to raise the squeegee/print arm for unobstructed access to screens.
Refers to squeegee pressure adjustment using a gauge on the arm.
Details the functions accessible via the control keypad for operating the machine in ADJUST-mode.
Explains how to access and use the submenu for additional settings like color type and delays.
Describes the squeegee carriage, its quick release mechanism, and adjustment features.
Introduces optional equipment that can be installed on the Synchroprint.
Guides on installing flash cure units, including power requirements and safety precautions.
Details the operation of flocking devices, emphasizing high voltage risks and protective measures.
Lists common basic errors and their fault clearance procedures, like control panel not booting.
Provides a table of error codes, messages, and troubleshooting steps for the control system.
Outlines the procedure for switching off the machine after a normal operational day.
Details the steps required for a scheduled long-term shutdown of the Synchroprint.
Explains the process for permanently decommissioning and disposing of the machine.
Specifies daily cleaning tasks for the machine and the surrounding print shop area.
Outlines weekly cleaning procedures for anodized parts, inspection glasses, and displays.
Provides instructions for cleaning the touchscreen, warning against aggressive cleaners.
Describes cleaning the automatic relief aperture of the water separator/trap.
Details lubrication points and recommended grease for the machine's central shaft.
General| Brand | MHM |
|---|---|
| Model | SYNCHROPRINT 5000 |
| Category | Industrial Equipment |
| Language | English |