Why booster cylinder doesn’t work in MHM SYNCHROPRINT 5000 Industrial Equipment?
The booster cylinder might not work if there is no air pressure at the booster cylinder. This could be due to incorrect adjustment of the lower pressure regulator or an active lower pressure stop cock.
Why the indexer doesn’t work in MHM SYNCHROPRINT 5000 Industrial Equipment?
The indexer might not work if the supply cable of the tablet is not connected. Connect the supply cable to the tablet.
What does error #0002 mean on MHM SYNCHROPRINT 5000?
Error #0002 indicates that the air pressure is too low. This could be due to a disconnected pressure hose, low pressure adjustment, or low supply pipe pressure.
What does error #0001 mean on MHM SYNCHROPRINT 5000?
Error #0001 indicates that the emergency stop circuit is interrupted. This could be because the emergency stop button has been pressed, a safety barrier has been opened, “Control ON/OFF” is off, or the reset button has not been pressed.
What to do if unlock screens does not work on MHM SYNCHROPRINT 5000?
If the unlock screens aren't working, consider the following: * The low pressure adjustment might be incorrect. Check the adjustment of the precision pressure regulator. * The valve might not be actuated. Check the wiring between the station PCB, Bus- PCB, and the squeegee valve.
What to do if squeegee does not toggle at squeegee carriage movement in MHM Industrial Equipment?
If the squeegee doesn't toggle during squeegee carriage movement, consider the following: * The squeegee pressure might be too low. Try adjusting the pressure control at the print station. * There might be no air pressure at the print station. Check if the lower pressure stop cock is active or if a tube has snapped off. * The valve might not be actuated. Check the wiring between the station PCB and the squeegee valve.
What to do if safety level cannot be adjusted on MHM Industrial Equipment?
If the safety level cannot be adjusted, it might be due to these reasons: * The safety key is not connected to the Distribution- PCB. Check the wiring from the safety key to the Distribution-PCB. * There is wrong wiring of the safety key at the panel housing. Take the terminal out of the housing and check the wiring of the safety key.
Provides guidance on using the operating instructions and notes on potential specification changes.
Explains the meaning of keywords and symbols used to denote dangers and important information.
Covers general safety regulations and the need for skilled staff for operation and maintenance.
Defines qualified personnel and lists responsibilities for safe operation and maintenance.
Details the specific skills and qualifications needed for various operating and maintenance tasks.
Outlines critical safety rules for operators, including keeping cabinets closed and using safety devices.
Specifies the required personal protective equipment for operators during work.
Identifies potential risks such as electrical, mechanical, and substance-related hazards.
Lists safety signs attached to the machine and their meanings and locations.
Reminds the customer to comply with all applicable regulations in the machine's operating country.
Explains how to use the EMERGENCY STOP button and safety bars to halt the machine.
Describes how the machine automatically stops the main drive upon detecting malfunctions.
Details the procedure for starting the machine, including checks and reference position initialization.
Introduces the MHM Hybrid-Control system and the control panels at print stations.
Explains controlling the machine via tablet or terminal and switching between them.
Guides on using the tablet PC for controlling main operating features through touch commands.
Explains using the "Adjust" menu on the tablet to configure the machine for the print job.
Describes operating the machine in manual mode, processing one index and working cycle at a time.
Details automatic mode where index and working cycles start continuously for production.
Covers elementary adjustments for machine setup, cleaning, and alignment via the BasicSetup menu.
Explains how the "Help" function supports troubleshooting and machine control.
Describes how operation can be automatically blocked and how to eliminate the blocking reason.
Explains operation using the fixed function keys and adjustable knobs on the terminal.
Details the "Adjust" function on the terminal for machine setup, including displays for direction and speed.
Describes operating in manual mode via the terminal, processing one index and working cycle.
Explains automatic mode via the terminal, where cycles start continuously after an index.
Covers error messages displayed on the terminal and tablet, including error codes and descriptions.
Details error messages displayed in red on the terminal with error number and text.
Explains error messages shown on the tablet, including error description and confirmation steps.
Indicates that the serial number and year of manufacture are found on the machine's type plate.
Presents diagrams showing the dimensions of various Synchroprint models.
Provides detailed technical specifications for different Synchroprint models in a table format.
Covers general safety notes for transportation, including falling objects and proper lifting procedures.
Describes that the Synchroprint is packed in wooden crates and provides information on variations.
Details the customer's responsibility for unloading and the required equipment, warning of mechanical damage.
States that installation must be performed by MHM service technicians to avoid warranty cancellation.
Guides on mounting the machine on a load-bearing bed and maintaining adequate distance from surroundings.
Specifies optimal ambient conditions like temperature, humidity, and air quality for machine operation.
Locates connections for compressed air and mains electricity on the base unit.
Details the electrical requirements, including supply voltage, frequency, and connected load.
Outlines the necessary compressed air specifications, including type of machine, consumption, and pressure.
Explains the step-by-step printing process from substrate application to unloading.
Identifies key components of the Synchroprint machine with labels on an image.
Provides an overview of the main control panel, including buttons like EMERGENCY STOP and tablet interface.
Lists and describes the machine's safety devices, such as EMERGENCY STOP buttons and safety bars.
Details the types of pallets used, their dimensions, and the maximum allowed weight.
Explains the function of the foot switch for starting index movements in manual mode.
Indicates the location of the type plate containing machine identification details.
Describes the main power switch's location and function for immediate disconnection from power.
Introduces print stations used for printing individual colors and mentions manual/automatic versions.
Shows a labeled diagram of the components of a manual print station.
Details individual parts of the manual print station, including the squeegee arm motor and dryer connector.
Explains how to adjust screen positioning using hand wheels for precise alignment.
Describes adjusting the squeegee carriage travel for reduced printing times and increased production.
Explains how to raise the squeegee/print arm for unobstructed access to screens.
Refers to squeegee pressure adjustment using a gauge on the arm.
Details the functions accessible via the control keypad for operating the machine in ADJUST-mode.
Explains how to access and use the submenu for additional settings like color type and delays.
Describes the squeegee carriage, its quick release mechanism, and adjustment features.
Introduces optional equipment that can be installed on the Synchroprint.
Guides on installing flash cure units, including power requirements and safety precautions.
Details the operation of flocking devices, emphasizing high voltage risks and protective measures.
Lists common basic errors and their fault clearance procedures, like control panel not booting.
Provides a table of error codes, messages, and troubleshooting steps for the control system.
Outlines the procedure for switching off the machine after a normal operational day.
Details the steps required for a scheduled long-term shutdown of the Synchroprint.
Explains the process for permanently decommissioning and disposing of the machine.
Specifies daily cleaning tasks for the machine and the surrounding print shop area.
Outlines weekly cleaning procedures for anodized parts, inspection glasses, and displays.
Provides instructions for cleaning the touchscreen, warning against aggressive cleaners.
Describes cleaning the automatic relief aperture of the water separator/trap.
Details lubrication points and recommended grease for the machine's central shaft.
General| Brand | MHM |
|---|---|
| Model | SYNCHROPRINT 5000 |
| Category | Industrial Equipment |
| Language | English |
To Next Page
