What to do if Mindray Medical Equipment system warns “OPERATING SYSTEM NOT FOUND”?
If your Mindray Medical Equipment displays the error message “OPERATING SYSTEM NOT FOUND”, it indicates that the OS loading failed, or the HDD or the root directory of OS is damaged. You should first try to restore the OS. If that doesn't work, replace the HDD.
What causes dark strips on the B image of Mindray Medical Equipment?
Dark strips on the B image of Mindray Medical Equipment can be caused by several issues: a malfunctioning probe (array damage - confirm by connecting another probe, and replace the transducer if it is), some transmission channels unable to generate transmission waveforms (replace the transmission board if dark strips appear in the near field), failure on the receiving channels (replace the receiving board if dark strips appear in the far field), or a malfunction on the probe board (replace the probe board assembly if dark strips appears casually for one probe with different sockets).
Why is there no image echo in the ultrasonic image region of Mindray DC-8 EXP Medical Equipment?
The absence of an image echo in the ultrasonic image region, despite probe recognition, may be due to a PHV voltage output of 0V or an abnormal voltage. It could also indicate a malfunction on the transmission board, front-end power main board or probe board. The probability of malfunction on the transmission board is higher than that of the front-end power main board PCBA. The third is probe board. Replace transmission board, front-end power main board or probe board to confirm the malfunction.
How to troubleshoot Mindray Medical Equipment with noise on the B image?
Noise on the B image in Mindray Medical Equipment can stem from a malfunctioning probe (confirm by connecting another probe and replace the transducer if it is). Alternatively, interference from other electrical equipment in the same network may be the cause. Try turning off nearby electrical equipment or disconnecting the system to confirm.
What to do if LCD is blank screen after entering BIOS start-up graphics on Mindray DC-8 EXP Medical Equipment?
If the LCD screen is blank after entering the BIOS start-up graphics on your Mindray Medical Equipment, it means that the OS can’t keep on loading, and the directory of HDD may be damaged. First restore, or else replace the HDD.
Why does Mindray DC-8 EXP BIOS start-up graphics is normally displayed, but it cannot be kept on?
If the BIOS start-up graphics on your Mindray Medical Equipment is normally displayed, but it cannot be kept on, it indicates a CPU Module malfunction. Replace the CPU module.
Why does Doppler start-up graphics is normally displayed on Mindray DC-8 EXP, but it cannot be kept on?
If the Doppler start-up graphics on your Mindray Medical Equipment is normally displayed, but it cannot be kept on, it means that Doppler can’t keep on loading, and the directory of HDD or HDD may be damaged. First restore, or else replace the HDD.
What to do if Mindray Medical Equipment AC indicator is ON, power-on status indicator keeps flashing, and power supply status indicators are all off?
If the AC indicator is ON, the power-on status indicator keeps flashing after pressing the power button, and the power supply status indicators (3.3V, 5V, and 12V) are all off on your Mindray Medical Equipment, the power board responds to power button, but the CPU module cannot respond on-off of power module. A likely cause (90% probability) is a malfunction on the CPU module. Replace the CPU module.
What to do if Mindray DC-8 EXP Medical Equipment AC indicator is ON, power-on status indicator doesn’t flash or is off, and power supply status indicators are all off?
If the AC indicator is ON, the power-on status indicator doesn’t flash or is off after pressing the power button, and the power supply status indicators (3.3V, 5V, and 12V) are all off on your Mindray Medical Equipment, a likely cause (90% probability) is a malfunction on the back-end power board PCBA. Replace the back-end power board PCBA.
What to do if Mindray Medical Equipment backlight status is normal but the LCD is blank screen, displaying “NO Signal”?
If the backlight status is normal when powering on the control panel but the LCD shows a blank screen with “NO Signal” on your Mindray Medical Equipment, the system can be powered on normally, and then enters into BIOS self-test stage, but no BIOS display screen, which indicates the failure of the CPU module. Replace the CPU module.
Guides users through the initial steps for configuring system presets before measurements.
Details how to configure specific measurement parameters like rulers and cursors.
Explains the settings and configurations specific to obstetric measurements and calculations.
Outlines the fundamental steps for performing general measurements on the system.
Details the necessary steps and checks before commencing an abdominal exam.
Guides users through the core procedures for taking abdominal measurements.
Outlines the setup and preparatory steps for obstetric examinations.
Details the fundamental procedures for taking obstetric measurements.
Explains Gestational Age calculation methods, including clinical and ultrasound GA.
Lists and describes the specialized measurement tools for obstetric applications.
Details the operational procedures for utilizing obstetric measurement tools.
Guides on performing measurements and managing data for multiple fetuses.
Details the necessary preparations before conducting cardiac examinations.
Outlines the fundamental steps for performing cardiac measurements.
Lists and describes the various measurement tools specific to cardiac imaging.
Explains the operational procedures for using cardiac measurement tools.
Details the preparatory steps required before performing vascular examinations.
Explains the operational procedures for performing HIP measurements.
General| Touch Panel | Yes |
|---|---|
| Operating System | Windows-based |
| Operating Temperature | +10°C to +40°C |
| Transducer Ports | 4 |
| Imaging Modes | B, M, Color, Power, PW, CW |
| Advanced Imaging Technologies | iClear |
| Type | Ultrasound System |
| Probe Connectors | 4 |
| Power Supply | 100-240VAC ±10%, 50/60Hz |
| Power Consumption | 500 VA |
| Storage Temperature | -20°C to +55°C |
| Relative Humidity | 30% to 80% (non-condensing) |
To Next Page
