Mindray DC-70 Exp

Questions and Answers:

F
fhillSep 15, 2025
What to do if Mindray Medical Equipment IO interface system has LCD works normally, but NO video printer output when pressing ?
- J
  James BrownSep 15, 2025
  If the LCD works normally on your Mindray Medical Equipment, but there is no video printer output when pressing on the control panel, it could be due to a USB connection error or a PC carrier board error. Re-plug the USB. Plug it into another USB port to confirm. Use a U disk to confirm whether other USBs work well. If the USB port is abnormal, replace the PC carrier board.
J
Jonathan PenaAug 25, 2025
What to do if the Mindray Medical Equipment AC indicator is on, the power on indicator blinks green, and the power status indicator (3.3 V/5 V/12 V) is off?
- T
  Tracy SpenceAug 25, 2025
  If the AC indicator remains on, the green power on indicator blinks after pressing the power button, and the power status indicator (3.3 V/5 V/12 V) is off, the PC module is likely the cause. Replace the PC module.
R
Rachel ForbesAug 25, 2025
What to do if the Mindray DC-70 Exp Medical Equipment AC indicator is on and the power on indicator blinks yellow?
- R
  Robin WoodsAug 26, 2025
  If the AC indicator remains on and the power on indicator starts to blink yellow after pressing the power button, the DC-DC board likely fails to respond. Replace the DC-DC board.
M
Michelle JacksonAug 26, 2025
How to troubleshoot a Mindray DC-70 Exp Medical Equipment when the AC power indicator remains off?
- J
  johnnybrandtAug 26, 2025
  If the AC power indicator remains off, it could be due to no AC input or errors on the AC-DC assembly. Check the AC connection. If the issue persists, replace the AC-DC assembly.
M
morganwaltersSep 16, 2025
What to do if Mindray DC-70 Exp control panel has some or a certain key on the small keyboard fails?
- E
  Elizabeth LiuSep 16, 2025
  If some or a certain key on the small keyboard fails on your Mindray Medical Equipment control panel, replace the small keyboard assembly.
D
David WilliamsSep 23, 2025
What to do if Mindray Medical Equipment system cannot power on?
- S
  Sarah WallaceSep 23, 2025
  If the Mindray Medical Equipment system fails to power on, begin by checking the backlight of the power button. Also, inspect the AC indicator on the control panel and verify the three power supply indicators on the IO back board.
N
nwallaceSep 8, 2025
What to do if Mindray DC-70 Exp IO interface system fails to recognize Wi-Fi?
- L
  larryvegaSep 8, 2025
  If your Mindray Medical Equipment fails to recognize Wi-Fi, check the 3.3 V indicator on the IO board. If it's brighter or off, the PC carrier board may be the issue, so replace it. If the network and settings are correct, the Wi-Fi board or PC carrier board may be faulty, so replace the Wi-Fi board or PC carrier board.
M
Michelle BellSep 8, 2025
What to do if Mindray Medical Equipment has no echo in ultrasound image?
- C
  Carolyn HintonSep 9, 2025
  If there is no echo in the ultrasound image on your Mindray Medical Equipment, even though the probe is recognized, it could be due to a PHV voltage output of the power module being 0 V or abnormal, or errors on the TR64 board, DC-DC board, or probe board. Confirm the error by replacing the TR64 board, DC-DC board, or probe board.
K
Kayla KramerSep 2, 2025
What causes dark strips on B image in Mindray Medical Equipment?
- D
  David SmithSep 2, 2025
  Dark strips appearing on the B image of your Mindray Medical Equipment can be caused by a probe malfunction, such as array corruption. Replace the probe. Alternatively, replace the TR64 board. If the strip is not fixed well for a single probe, the probe board may be faulty, so replace the probe assembly.
J
Jasmine WellsAug 31, 2025
What to do if Mindray DC-70 Exp system cannot start and BIOS start-up graphics is normally displayed, but it does not last?
- J
  Jeffrey AshleyAug 31, 2025
  If the BIOS start-up graphics are normally displayed on your Mindray Medical Equipment, but it does not last, it indicates a PC module failure. Replace the PC module.

Mindray DC-70 Exp Specifications

General

Touch Screen Size	10.4 inch
Probe Ports	4
Power Supply	100-240V AC, 50/60Hz
Connectivity	DICOM, USB, Ethernet
Applications	Abdominal, Cardiac, OB/GYN, Vascular
Weight	85 kg
Doppler Modes	PW, CW, Color Doppler, Power Doppler
Imaging Modes	2D, M-Mode, 4D
Storage	500GB hard drive