To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...Why isn't the touchscreen of the external display working with my Mindray T1 Medical Equipment?
If the touchscreen of the external display isn't working, it could be a USB connection error. Reinstall or restart T1.
Why does the external display turn black when T1 is installed to the T1 Docking Station on my Mindray Medical Equipment?
If the external display turns black when T1 is installed to the T1 Docking Station, it might be due to: * An error caused by hot plug. Reinstall T1. * An incorrect connection sequence. Connect the external display and T1 Docking Station first and then install or start T1.
What to do if Mindray Medical Equipment T1 fails to start when running on battery?
If the T1 fails to start when running on battery, consider these potential causes: * **Low charge or defective battery:** Charge the battery properly and test for proper voltage reading. If the battery does not charge properly, replace it. * **Defective Infrared board:** If the battery works properly, and T1 works properly when connected to the external power source, verify the infrared board is installed. If properly installed but not working, replace the infrared board.
Why is there no video output from my Mindray Medical Equipment?
If there is no video output, it may be caused by: * A defective Dock interface board. Replace the Dock interface board. * A defective Dock converter board. Replace the Dock converter board. * A defective main board of the Docking Station. Replace the main board of the Docking Station.
Why is my Mindray T1 Medical Equipment failing to identify parameter modules?
If the device fails to identify parameter modules, it could be due to: * A defective T1 handle NIOS board. Replace the T1 handle NIOS board. * A defective T1 handle converter board. Check the connection between the T1 handle converter board and the T1 handle NIOS board. If properly connected, replace the T1 handle converter board. * A defective main board. Replace the main board.
What to do if the lock/unlock switch does not respond on my Mindray Medical Equipment?
If the lock/unlock switch does not respond, the main board may be defective. Replace the main board.
What causes vertical or horizontal lines on the Mindray T1 display?
If vertical or horizontal lines are displayed, the display is defective. Replace the front housing assembly.
Why is there no alarm sound being issued from my Mindray T1?
If no alarm sound is being issued, consider the following possible causes: * The audible alarm is disabled. Check if the “ ” icon is displayed. If yes, the audible alarm is disabled. Also, check if the “ ” icon is displayed. If yes, the alarm is paused or turned off. * Defective connection. Verify the connection between the main control board and the parameter connector board or the connection between the parameter connector board and the speaker. * Defective speaker. Replace the speaker. * Defective main board. Replace the main board.
Why is the alarm LED not lighting up on my Mindray Medical Equipment?
If the alarm LED does not light up, the main board may be defective. Replace the main board.
What causes program upgrade failures in Mindray T1 Medical Equipment?
Program upgrade failures can occur due to: * **Incorrect network connection:** Check the network connector on the patient monitor. Ensure the hub or switch is operating correctly and the correct network cable is in use and connected correctly. * **Wrong upgrade package:** The upgrade package shall be .pkg files. Select the correct .pkg file for your application. * **Incorrect IP address setting:** Configure a fixed IP address in range C as specified for the patient monitor. It is recommended not to perform software upgrades when T1 is connected to a network having multiple PCs. * **Defective main board:** Replace the main board.
General| Category | Patient Monitor |
|---|---|
| Battery Life | Up to 4 hours |
| Imaging Modes | Not applicable |
| SpO2 | Yes |
| Pulse Rate | Yes |
| ECG | Yes |
| NIBP | Yes |
| Temperature | Yes |
| Parameters | ECG, SpO2, NIBP, Temperature, Respiration |
| Connectivity | USB, Ethernet, Wi-Fi |
Details on warnings, cautions, and notes for safe operation and handling of the patient monitor.
Procedures for upgrading the monitor's hardware, including IBP, ECG, and Wi-Fi functions.
Procedures for various performance tests including ECG, SpO2, NIBP, and others.
Tests for power-on, touchscreen calibration, battery, and network printing functionality.
Steps to access and utilize the factory maintenance menu for advanced settings.
Guide to identifying and resolving common problems with the patient monitor.
Specific tests and limits for electrical safety inspection as per standards.
