Name: multicomp pro MP720025
Brand: multicomp pro
Rating: 5 (1 reviews)

To Next Page

To Previous Page

User Manual

3. Click Reload Disk on the pull-down menu at the top left or push keyboard F5,

and information about the USB disk will display on the right side with red mark 1

and 2.

Figure 4-17: Reload Disk

4. Right click 1 or 2 red mark area, choose Format.

Figure 4-18: Choose format

5. Set File System FAT32, Cluster size 4096. Click OK.

Figure 4-19: Format setting

Table of Contents2
General Safety Requirements6
Safety Terms and Symbols7
Junior User Guidebook9
Introduction to the Structure of the Oscilloscope10
Front Panel10
Rear Panel11
Control Area12
User Interface Introduction13
How to Implement the General Inspection15
How to Implement the Function Inspection16
How to Implement the Probe Compensation16
How to Set the Probe Attenuation Coefficient17
How to Use the Probe Safely18
How to Implement Self-Calibration19
Introduction to the Vertical System19
Introduction to the Horizontal System21
Introduction to the Trigger System21
Touchscreen Controls (Touchscreen Is Optional)22
Advanced User Guidebook28
How to Set the Vertical System29
Use Mathematical Manipulation Function31
Waveform Math32
User Defined Function33
Digital Filter33
Using FFT Function34
Use Vertical Position and Scale Rotary Controls39
How to Set the Horizontal System40
Waveform Horizontal Zooming40
Magnifier (for Specific Models)41
How to Set the Trigger/Decoding System43
Single Trigger43
Logic Trigger53
Bus Trigger54
Bus Decoding (Optional)60
How to Operate the Function Menu65
How to Implement Sampling Setup65
How to Set the Display System67
How to Save and Recall a Waveform70
How to Record/Playback Waveforms77
How to Clone and Recall a Waveform81
How to Implement the Auxiliary System Function Setting86
How to Update Your Instrument Firmware89
How to Measure Automatically91
How to Measure with Cursors95
How to Use Autoscale98
How to Use Built-In Help100
How to Use Executive Buttons100
How to Print the Screen Image102
Use the Arbitrary Function Generator (Optional to Specific Models)103
Output Connection103
To Set Channels103
To Set Signals104
To Output Sine Signals104
To Set the Frequency104
To Set the Period105
To Set the Start Phase105
To Set the Amplitude105
To Set the Offset106
To Set the High Level106
To Set the Low Level106
To Output Square Signals106
To Output Ramp Signals106
To Set the Symmetry of Ramp106
To Output Pulse Signals106
To Set the Pulse Width of Pulse106
To Set the Duty Cycle of Pulse106
To Output Arbitrary Signals107
Create a New Waveform107
File Browse108
Built-In Waveform108
Frequency Response Analysis110
Use the Multimeter (Optional)112
Input Terminals112
DMM Menu112
DMM Information Window113
Making Multimeter Measurements114
Measuring AC or DC Current114
Measuring AC or DC Voltage114
Measuring Resistance115
Testing Diodes115
Testing for Continuity115
Measuring Capacitance115
Multimeter Features116
Data Hold Mode116
Making Relative Measurements116
Information Display116
Auto or Manual Range116
Multimeter Recorder116
Communication with PC119
Using USB Port119
Using LAN Port120
Connect Directly120
Connect through a Router121
Using Wi-Fi to Connect with PC (Optional)123
Connect with PC as Wi-Fi Access Point123
Connect with PC as Wi-Fi Station124
Communication with Android Device Via Wi-Fi (Optional)127
How to Connect127
Connect with APP as Wi-Fi Access Point127
Connect with APP as Wi-Fi Station129
User Interface131
Gestures Control133
Demonstration135
Example 1: Measurement a Simple Signal135
Example 2: Gain of a Amplifier in a Metering Circuit136
Example 3: Capturing a Single Signal137
Example 4: Analyze the Details of a Signal138
Example 5: Application of X-Y Function140
Example 6: Video Signal Trigger142
10. Troubleshooting143
11. Technical Specifications145
Oscilloscope145
Trigger148
Waveform Generator (Optional)149
Multimeter (Optional)150
General Technical Specifications151
12. Appendix152
Appendix A: Enclosure152

multicomp pro MP720025 User Manual

Table of Contents

Questions and Answers:

multicomp pro MP720025 Specifications

Related product manuals

Brand	multicomp pro
Model	MP720025
Category	Test Equipment
Language	English