EasyManuals Logo

Nabco GT20 Wire And Programming Manual

Nabco GT20
43 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #27 background imageLoading...
Page #27 background image
27 of 43
www.NabcoEntrances.com GT20 Wire and Programming Manual
Rev 5-7-18 P/N C-00140
SECTION 92: Menu Selecon
Table 9 
Menu
Description
PARAMETER Sets the parameters for Swing door movement.
CONFIG Conguraon: Sets the parameters of the GT20 Control Features and Funcons.
DOUBLE DOOR Sets the Closing sequence and Interlock funcon.
DIAGNOSTICS Diagnosc Tools that display the status of various inputs.
ERROR ACTIVE X Displays Pending Acve Errors.
X Acve Error list is updated with the latest addions appearing at the end.
X A0 indicates the latest Acve error.
HISTORY ERROR X Displays all Acve Errors that were detected and then corrected or not corrected.
X H0 indicates the latest Acve error.
REINIT Reinializaon resets Sengs back to Factory Default
BLOCK? Locks/Unlocks Joysck
UPDATE SW Start the upgrade process from the USB Sck.
TEACH X Programs the Inial Setup, and nds Errors (if any).
X Programs a new Setup Procedure when deemed necessary.
Table 10 
Element
Unit Type Default Value Description
Region BOTH EU Eu or US EU - Europe; US - United States
Soware version determined by UL Standards. Must be changed to US.
Vo Full Power 6 0..14 Opening speed (velocity open)
Low Energy 9 0...9
Vc Full Power 4 0..14 Closing speed (velocity closed)
Low Energy 9 0...9
TOEx Full Power 3s 0...60s TOEx sets the hold-open me resulng from acvaon signals from devices
connected to: terminals 9+10 for exterior acvaon and terminals 12+13 for
interior acvaon.
Low Energy 5s 3...60s
ANSI 156.19 for Low Energy:
TOEx must be no less than 5s.
TKey Full Power 5s 0...180s X TKey sets the hold-open me resulng from an acvaon signal from a device
(referred to as KEY) on terminals 2+3.
X With TOEx and TKey, you can set a dierent hold open mes for dierent
acvaon devices by using dierent terminals.
Low Energy 5s 3...180s
TPuGo Full Power 3s 0...180s Determines how long the Door Panel stays open.
Low Energy 3s 3...180s
TDelay Full & Low 0.2s 0.0...4.0s Tdelay sets the amount of me the door hesitates to allow the lock to release
before opening.
FDelay Full Power OFF OFF...7.0A Fdelay is a temporary “hold closed” force applied to the door to keep it closed
while the electric lock is being released. This parameter sets the amount of force
that is applied. FDelay is only acve if TDelay seng is greater than 0.
Low Energy OFF OFF...7.0A
TLock Full & Low 0.5s 0.0...4.0s Sets amount of me Door Panel will press against lock to engage it.
FLock Full & Low 2.0A OFF...7.0A Sets amount of force that is applied to the door to engage the lock at the closed
posion. It is only acve if TLock seng is greater than 0.
FSlam Full & Low OFF OFF...10 Accelerang funcon (force slam). For example: When a door panel needs to be
forced shut due to a latch or heavy seals.

Other manuals for Nabco GT20

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Nabco GT20 and is the answer not in the manual?

Nabco GT20 Specifications

General IconGeneral
BrandNabco
ModelGT20
CategoryDoor Opening System
LanguageEnglish

Related product manuals