Nice AVIO500 - Selection of the Type of Devices Connected to S1 Edge; Other Functions; Activating;Deactivating the Control Unit Protection Device

10.2 – SELECTION OF THE TYPE OF DEVICES CON-
NECTED TO “S1 EDGE”
Default = “S1 Edge” set for devices with normally closed
contact (terminal 9)
Thisprocedureallowsforsettingthe“S1Edge”outputformanag-
ing8.2kOhmresistiveedges.
The control unit constantly veries the integrity of the edge by
10.3 – OTHER FUNCTIONS
To interrupt the following programming sequences at
any time, press the SET and RADIO buttons simultaneously
or wait 10 seconds.
ACTION RESULT
01. PRESS STARTBUTTONFOR3SECONDS
AlltheLEDsturnoff(ifnot,consult
Paragraph10.3.1)
02.
PRESS THE RADIOBUTTONFOR1SECONDandthenchooseoneofthe
following:
• S1 Edge = resistive edge > 03.a
• S1 Edge = device with normally closed contact (NC) > 03.b
03.a
S1 Edge = resistive edge:theyellow“set”lightisON.
Ifthesettingiscorrect,proceedtoitem05;otherwise,goto04.a
Thered“error”LEDturnsoninthefixed
mode
04.a
Device with normally closed contact (NC):
PRESS THE STARTBUTTONFOR1SECOND
Thered“error”LEDremainslitinthefixed
modeandtheyellow“Set”LEDturnsoff
OR
03.b
S1 Edge = device with normally closed contact (NC): theyellowLED
“set”lightisOFF.
Ifthesettingiscorrect,proceedtoitem05;otherwise,goto04.b
Thered“error”LEDturnsoninthefixed
mode
04.b
Stop the programming sequences:
PRESSBOTHTHESTARTANDRADIOBUTTONSFOR2SECONDS
Thered“error”LEDremainslitinthefixed
modeandtheyellow“Set”LEDturnson
05.
PRESS THE SETANDRADIOBUTTONS
SIMULTANEOUSLYORWAIT10SECONDSTOEXITTHEPROCEDURE
TheLEDsreturntothenormaloperation
conguration
ACTION RESULT
01. PRESS STARTBUTTONFOR3SECONDS AlltheLEDsturnoff
02.
PRESS THE SETBUTTONFOR1SECONDANDTHENSELECTONEOF
THEFOLLOWING:
• control unit block activated > 03.a
•controlunitblockdeactivated>03.b
03.a
Control unit block activated: yellow“set”LEDlight,red“radio”LEDlight
andred“error”LEDlightareON.
Ifthesettingiscorrect,proceedtoitem05;otherwise,goto04.a
04.a
Unlocking programming sequences:
PRESSBOTHTHESTARTANDRADIOBUTTONSFOR2SECONDS
Theyellowled“set”,theredled“radio” and
redled“start” go OFF
OR
03.b
Control unit block activated: yellow“set”LEDlight,red“radio”LEDlight
andred“error”LEDlightareOFF.
Ifthesettingiscorrect,proceedtoitem05;otherwise,goto04.b
04.b
Stop the programming sequences:
PRESSBOTHTHESTARTANDRADIOBUTTONSFOR2SECONDS
Theyellowled“set”,theredled“radio” and
redled“start” go ON
05.
PRESSBOTHBUTTONSSETANDRADIO
SIMULTANEOUSLYORWAIT10SECONDSTOEXITTHE
PROCEDURE
AlltheLEDsgobacktostandardbehavior
measuringtheresistancebetweenthetwodedicatedterminals.
In order to carry out the check on the safety devices,
the connected edges must be of the resistive type with 8.2
kOhm.
10.3.1 – ACTIVATING/DEACTIVATING THE CONTROL
UNIT PROTECTION DEVICE
Default = control unit protection device not active.
This programming sequence allows for locking all control unit
programmingsequencesandthesettingsadjustablethroughthe
dip-switches.Toperformanewprogrammingsequenceormake
adip-switch/trimmermodicationeffective,theprotection must
bedeactivated.
English–23
English