Nice AVIO500 - Transmitter Programming; Programming the Button Linked to the OUT1 Output; Programming the Button Linked to the On-Board Courtesy Light; Deleting All Memorised Transmitter

STEP 5
START
RADIO
SET
If, at the start of the following procedures, the “set”,
“radio” and “error” LEDs ash, it means that the program-
ming protections have been activated – see Paragraph
10.3.1.
Therefore, radio transmitters learning is not possible.
To interrupt the following programming procedures at
any time, press the RADIO button or wait 20 seconds.
5.1 – TESTING THE RADIO TRANSMITTER
Totestthetransmitterjustpressoneofits4keys,makesurethat
theredLED[A]ashesandthattheautomationcarriesoutthe
relatedcommand.
Thecommandassociatedtoeachbuttondependsonhowithas
beenmemorised.
[B]
[A] Led
T5
T2
T4
T3
T1
32
5.2 – START BUTTON PROGRAMMING
Thisprocedure allows forprogrammingthebuttonof the radio
controllinkedtotheautomation’sstartfunction.
ACTION RESULT
01.
PRESS THE RADIO
BUTTONFOR1
SECOND
Thered“radio”
LEDturnsoninthe
fixedmode(ifnot,
consultParagraph
10.3.1)
02.
PRESSTHEDESIRED
BUTTONONEVERY
TRANSMITTERTOBE
PROGRAMMED
Thered“radio”
LEDflashes
03.
PRESS THE RADIO
BUTTONUNTILRADIO
LEDTURNSOFFOR
WAIT20SECONDSTO
EXITTHEPROCEDURE
Thered“radio”
LEDturnsoff
TRANSMITTER PROGRAMMING
5.3 – PROGRAMMING OF THE BUTTON LINKED TO THE
“OUT1” OUTPUT
Thisprocedureallowstheprogrammingoftheremotecontrolbut-
tonconnectedtothe“OUT1”output(1-2terminals).
ACTION RESULT
01.
PRESS THE RA-
DIOBUTTONFOR1
SECOND
Thered“radio”LED
turnsoninthefixed
mode
02.
PRESS THE START
BUTTONFOR1
SECOND
Thered“radio”LED
remains lit in fixed
modeandthered
“error”LEDturns
on in fixed mode
03.
PRESSTHEDESIRED
BUTTONOFALLTHE
TRANSMITTERSTOBE
PROGRAMMED
Thered“radio”LED
flashesandthered
“error”LEDramins
lit in fixed mode
04.
PRESS THE RADIO
BUTTONUNTILRADIO
LEDTURNSOFFOR
WAIT20SECONDSTO
EXITTHEPROCEDURE
Thered“radio”LED
andthered“error”
LEDturnoff
5.4 – PROGRAMMING OF THE BUTTON LINKED TO THE
ON-BOARD COURTESY LIGHT
Thisprocedure allows forprogrammingthebuttonof the radio
controllinkedtotheon-boardledcourtesylight.
ACTION RESULT
01.
PRESS THE RA-
DIOBUTTONFOR1
SECOND
Thered“radio”LED
turnsoninthefixed
mode
02.
PRESS THE SET
BUTTONFOR1
SECOND
Thered“radio”
LEDremainslitin
fixedmodeandthe
yellow“set”LED
turns on in fixed
mode
03.
PRESSTHEDESIRED
BUTTONOFALLTHE
TRANSMITTERSTOBE
PROGRAMMED
Thered“radio”
LEDflashesandthe
yellow“set”LED
ramins lit in fixed
mode
04.
PRESS THE RADIO
BUTTONUNTILRADIO
LEDTURNSOFFOR
WAIT20SECONDSTO
EXITTHEPROCEDURE
Thered“radio”LED
andtheyellow“set”
LEDturnoff
5.5 – DELETING ALL MEMORISED TRANSMITTER
This operation deletes all memorized transmitters from the
memory.
ACTION RESULT
01.
PRESS THE RADIO
BUTTONFOR4
SECONDSAND
RELEASEWHEN
RADIOLEDFLASHES
Thered“radio”LED
ashes
02.
PRESS THE RADIO
BUTTONAGAIN
FOR1SECOND
Thered“radio”LED
ashesfast
03.
MEMORYDELETION
COMPLETED
Thered“radio”LED
turns off
5.6 – DELETING A SINGLE TRANSMITTER
Thisoperationdeletesasingletransmitterfromthememory.
16–English
English