Chapter 14 - Phone interface 14-9
from the operator. Press
OK
or the
key.
At the prompt
Topic name
, key in the name
(10 letters) and press
OK
. The new subject
is added to the option list.
To turn off the broadcast messages function,
choose
Off
and press
OK
.
To erase subjects that you have added to the
topics list, choose
Erase
and press
OK
. Choose
a topic and press
Erase
.
To read broadcast messages, use or to
scroll through the topic list. Press
OK
to select
a topic. The header of the topic and the text
WAIT are displayed. You can scroll the text
with or . Pressing the left selection key
gives you the following options:
Use number
– Copies the phone number
from the current message onto the dis-
play, from which you can dial it or store it
elsewhere. (Instead of this function, you
may press while viewing the mes-
sage.) You can dial the number or store it
elsewhere in the normal way.
Off
– Turns the cell broadcast receiving
off.
If you want to read a message again, choose the
message from the menu. The message will appear
immediately on the display.
Voice call diverting (Menu 3)
The call divert network service allows you to di-
rect your incoming calls to another phone
number when you do not want to be disturbed,
or when the phone interface is switched off or
outside of the network coverage area. The call di-
verting functions are described in more detail in
chapter 4 "Telephone: Telephone settings - Voice
call diverting"
Note:
Call diverts made via the phone interface
only apply to voice calls. Fax divertings are made
in the Fax application’s settings (see chapter 5
"Fax: Fax settings").
Select the desired call divert mode in the
main menu:
Divert all voice calls (Menu 3 1)
,
Divert when
busy (Menu 3 2)
,
Divert when not answered
(Menu 3 3)
,
Divert if not reachable (Menu 3 4)
,
Cancel all diverts (Menu 3 5)
Unless you chose
Cancel all diverts
, the follow-
ing options are now available:
Press or to move the pointer to
Activate
(set divert mode on). You will be asked for the
phone number to which you wish to divert the
incoming voice calls (to your voice mailbox or
some other number). See chapter 4 "Telephone:
Telephone settings - Voice call diverting" for de-
tails.
When the phone interface is in the idle state (you
have no active calls and you are not in any
menu), you can also modify the phone number by
using a manual command string. The delay time
(after which the call divert is activated) can be
modified by a manual command string only: for
the required command strings, contact your net-
work operator.
Cancel
sets the divert mode off.
Status
shows call types which are being diverted.
Phone settings (Menu 4)
Lights (Menu 4 1)
The keypad and display of the phone interface
are fitted with lights to make them easy to
read. When the communicator is used as a
handportable phone or is connected to a
charger, this setting determines whether the
lights remain on for 15 seconds after the last
keystroke or an incoming call alert (
On
) or re-
main permanently off (
Off
).
The lights can be switched on for 15 seconds
by pressing quickly even if
Off
is selected.
When the communicator is connected to a
handsfree car kit, the lights always remain on
(
On
) or extinguish after 15 seconds (
Off
).
Ringing volume (Menu 4 2)
The ringing tone will be heard when you re-
ceive a call. There are several ringing tone
volume levels available. If you have set the
communicator in silent service within Menu
10, the ringing tone will not be heard.
Ringing tone (Menu 4 3)
You can select from a range of different tone
patterns. When you change the ringing tone,
daphne.frm Page 9 Wednesday, January 15, 1997 1:48 PM
To Next Page
Loading...
