To Next Page

To Previous Page

About The Meter

2.3 AVAILABLE ACCESSORIES

Table 2-1. Accessories and Add-Ons

Add-On Options

FS Special Calibration/Configuration

SPC4 NEMA-4 Splash Proof Cover

SPC18 NEMA-4 Splash Proof Cover, NEW

Accessories

TP1A Trimplate panel adaptor.

Adapts DIN1A/DIN2A cases to larger panel cutouts

RP18 19-In. Rack Panel for one (1) 1/8 DIN instrument

RP28 19-In. Rack Panel for two (2) 1/8 DIN instruments

RP38 19-In. Rack Panel for three (3) 1/8 DIN instruments

Table of Contents5
Sec11
- Introduction11
- Unpacking11
- Safety Considerations12
Sec13
- About the Meter13
- Description13
- Features13
- Available Accessories14
- Front of the Meter15
- Back of the Meter18
Connector Description19
- Disassembly20
Getting Started21
- Rating/Product Label21
- Main Board Power Jumpers21
Main Board Jumper Positions22
Upper Isolated Analog Output Option Board Installation22
S3 Jumper Functions23
- Panel Mounting24
Meter - Exploded View24
- Connecting Sensor Inputs25
Meter-Powered Bridge Input25
Externally-Powered Bridge Input25
Wire DC Input Connections with External Excitation26
- Connecting Main Power27
Current Input Connections with Internal Excitation26
Current Input Connections with External Excitation27
Main Power Connections - AC27
Main Power Connections - DC28
- Connecting External Tare Switch29
- Connecting Analog and Relay Outputs29
External Tare Connections29
Analog Output Connections29
Relay Output Connections30
Isolated Analog Output Connections30
Sec31
- Configuring the Meter31
- Selecting the Input Type31
- Selecting a Decimal Point Position32
- Selecting Reading Scale and Offset32
- Scaling with Known Loads33
- Scaling Without Known Loads36
- Using Reading Configuration37
- Selecting Ratiometric/Non-Ratiometric Operation38
- Setting Input Resolution38
- Displaying the Filtered/Unfiltered Input Signal39
- Selecting Gross/Net or Peak Display39
- Selecting a Display Color40
- Using Setpoint 1 Configuration40
- Setting Setpoint 1'S Active Band41
- Selecting if Setpoint 1 Is Latched or Unlatched41
- Assigning Setpoint 1 Values to Net or Gross Readings42
- Using Setpoint 2 Configuration42
- Setting the Setpoint 2'S Active Band42
- Selecting if Setpoint 2 Is Latched or Unlatched43
- Assigning Setpoint 2 Values to Net or Gross Readings43
- Setting the Setpoint 1 Deadband44
- Setting the Setpoint 2 Deadband45
Alarm Example46
- Using Output Configuration47
- Enabling or Disabling the Analog Output47
- Selecting Analog Output as Current or Voltage48
- Selecting Analog Output or Proportional Control48
- Using Output Scale and Offset49
- Examples of Output Scale and Offset51
- Using Lock out Configuration52
- Enabling or Disabling the RESET Button in the Run Mode52
- Enabling or Disabling Setpoint Changes52
- Setpoint Display Function: Firmware Version or Setpoint Value53
- Using Display Brightness Configuration53
- Changing Brightness Level53
Display Messages54
Menu Configuration Displays55
Sec56
Run Mode Displays58
- Setpoint Configuration Displays59
Sec60
- Specifications60
Sec61
Panel Cutout62
Color Chart for DC Power63
Meter Dimensions/Panel Cutout64
- Factory Preset Values65
Sec 10 Ce Approval Information66

Brand	Omega
Model	DP25B-S
Category	Measuring Instruments
Language	English

Omega DP25B-S User Manual

Table of Contents

Other manuals for Omega DP25B-S

Questions and Answers:

Omega DP25B-S Specifications

Related product manuals