Omron E5AR - MANUAL 2 - Page 340

Index
Numerics
3-position control .................................... 4-18
A
A/M key ..................................................... 1-6
Address (Communication/Modbus) ...7-8, A-6
Addresses
(Communication/CompoWay/F) ........6-7, A-6
Adjustment 2 level .........................8-22, A-13
Adjustment level ............................8-12, A-12
Advanced function setting level .....8-67, A-26
Alarm 1 ................................................... 8-28
Alarm 2 ................................................... 8-28
Alarm 3 ................................................... 8-28
Alarm 4 ................................................... 8-28
Alarm hysteresis ............................ 5-26, 8-56
Alarm latch ..................................... 5-27, 8-55
Alarm lower limit ..................................... 8-29
Alarm setting level .........................8-53, A-23
Alarm types .................................... 4-24, 8-54
Alarm upper limit ..................................... 8-29
Alarm values ........................................... 4-25
Alfa .......................................................... 8-76
Analog input calibration ............................ 9-8
Analog parameter ................................... 8-25
Approximation setting level ............8-33, A-16
ASCII Codes ............................................. A-5
AT (Auto-tuning) ............................ 4-20, 8-13
AT calculated gain .................................. 8-78
AT cancel ....................................... 6-23, 7-23
AT execute ..................................... 6-23, 7-23
AT Execute/Cancel ................................. 8-13
AT hysteresis .......................................... 8-78
Auto/Manual ........4-30, 5-30, 6-27, 7-27, 8-11
Automatic selection range upper limi ...... 5-12
Auxiliary output assignment .. 1-11, 4-23, 8-48
Auxiliary output non-exciting .......... 5-27, 8-58
Auxiliary outputs (terminals) ................... 2-13
B
Bank change .................................. 6-22, 7-22
Bank No. ................................................. 8-13
Bank No. (Bits 0 to 2) .............................. 5-30
Bank setting level ...........................8-26, A-14
Banks ................................................. 1-2, 5-9
Bar graph display items .......................... 8-61
Broken-line approximation ............... 5-6, 8-34
Broken-line approximation enable .......... 8-51
Bumpless run .......................................... 8-79
C
Cancel latch ................................... 6-28, 7-28
Cascade control ...................................... 3-13
Cascade heating/cooling control ...... 1-9, 4-13
Cascade open/close ................................ 8-14
Cascade standard control ................ 1-9, 4-13
CH2 (operation indicator) .......................... 1-5
Changing channels ................................. 4-31
Channel indication ..................................... 1-5
Close in alarm/Open in alarm .................. 5-27
Closed/Floating .............................. 3-12, 8-44
CMW (operation indicator) ........................ 1-5
Cold junction compensation .................... 8-75
Commands and responses
(Communication/CompoWay/F) .............. 6-14
Commands and responses
(Communication/Modbus) ....................... 7-17
Communication (terminals) ..................... 2-17
Communication data length .................... 8-65
Communication parity ............................. 8-65
Communication protocol selection .......... 8-64
Communication setting level ..........8-63, A-25
Communication speed ............................ 8-64
Communication stop bit ........................... 8-65
Communication Unit No. ......................... 8-64
Communication write OFF/ON ................ 5-29
CompoWay/F communication protocol ..... 6-2
Connecting the cold junction compensator 9-5
Connections .............................................. 2-4
Constant at disturbance .......................... 5-14
Control / Transfer output assignment ...... 4-15
Control initial setting level ..............8-41, A-18
Control initial setting level 2 ...........8-45, A-19
Control mode ..................................4-13, 8-43
Control outputs / Transfer outputs
(terminals) ............................................... 2-12
Control period .......................................... 4-14
Control period (cooling) ........................... 8-16
Control period (heating) .......................... 8-16
Control/Transfer output allocation .. 1-10, 8-46
Cooling coefficient ............................3-8, 8-15
D
Dead band ........................................3-8, 8-15
Decimal point position ............................. 8-37
Derivative time ........................................ 8-31
Dimensions ............................................... 2-2
Direct operation ....................................... 4-14
Direct operation (cooling) .......................... 1-9
Display 1 ................................................... 1-5
Display 2 ................................................... 1-5
Display 3 ............................................ 1-5, 4-3