Omron E5AR - MANUAL 2 - Page 341

Display adjustment level ................8-59, A-24
Display auto-return time .......................... 8-61
Display PID selection .............................. 8-30
Display refresh period ............................. 8-61
Display scan ............................................ 5-19
Display scan period ................................. 8-62
Disturbance gain ............................ 5-14, 8-21
Disturbance judgment width .................... 8-21
Disturbance overshoot adjustment ......... 5-14
Disturbance overshoot
adjustment function ........................ 5-14, 8-80
Disturbance rectification band ................. 8-21
Disturbance time constant ...................... 8-21
Down key .................................................. 1-6
E
Echo back test ........................................ 7-29
End codes
(Communication/CompoWay/F) ................ 6-5
Error messages ....................................... 10-3
Event input .............................................. 5-29
Event input allocation ..................... 5-29, 8-47
Event inputs (terminals) .......................... 2-15
Expansion control setting level ......8-72, A-27
Explanation of the keys ............................. 1-6
Extraction of square root low-cut point .... 8-24
Extraction of square root operations ......... 5-7
F
First order lag operation ............................ 5-5
First order lag operation enable .............. 8-50
First order lag operation time constant ... 8-22
Forward/reverse operation ...................... 8-44
Frames (Communication/CompoWay/F) .. 6-4
Front .......................................................... 1-4
Function codes (Communication/Modbus) 7-7
Function key 1 ........................................... 1-6
Function key 2 / channel key .................... 1-6
H
Heating/cooling control .............1-9, 3-5, 4-13
Heating/cooling control
with remote SP ................................. 1-9, 4-13
Hysteresis ............................................... 4-18
Hysteresis (cooling) ................................ 8-16
Hysteresis (heating) ................................ 8-16
I
Indicator (control) ranges .......................... A-4
Inferring causes from conditions ............. 10-4
Initial setting examples .............................. 4-5
Initial setting protect ................................ 5-24
Initialization due to setting changes ........ A-28
Initialize settings ............................. 6-27, 7-27
Input error ............................................... 10-3
Input initial setting level ................. 8-35, A-17
Input shift ..........................................5-2, 8-20
Input type .........................................4-8, 8-36
Input type switch error ............................. 10-3
Input/output configuration .......................... 1-7
Inputs (terminals) .................................... 2-12
Inspecting indicator accuracy .................. 9-13
Installation procedure ................................ 2-3
Insulation blocks ...................................... 2-18
Integral time ............................................ 8-31
K
Key operation (event input) ..................... 5-29
L
Level key ................................................... 1-6
Limit cycle ............................................... 4-21
Limit cycle MV amplitude ........................ 8-78
Limitations during SP ramp ....................... 5-9
Linear current output output type ............ 8-42
List of service
(communication/CompoWay/F) ................. 6-6
Local SP ...........................................5-9, 8-27
Location of input type switch ..................... 1-8
M
MANU (operation indicator) ....................... 1-5
Manual .................................................... 4-29
Manual mode .......................................... 4-29
Manual MV ................................................ 8-5
Manual MV initial value ........................... 8-77
Manual output method ............................ 8-77
Manual reset value .................................. 8-15
Manual settings ....................................... 4-22
Modbus communication protocol .............. 7-2
Mode key ................................................... 1-6
Monitor item level setting ........................ 8-62
Monitor value / setting data compound read
(Communication/CompoWay/F) .............. 6-16
Monitor value / setting data compound read
store (write) ............................................. 6-19
Monitor value / setting data compound read
store check (read) ................................... 6-20
Monitor value / setting data compound store
read ......................................................... 6-20
Monitor value read
(Communication/CompoWay/F) .............. 6-14
Monitor value read
(Communication/Modbus) ....................... 7-17
Monitor/Setting item ................................ 5-22
Motor calibration .............................3-12, 8-52
Motor calibration error ............................. 10-3
Move average ..................................5-5, 8-23
Move to advanced function setting level . 8-40
Move to calibration level .......................... 8-71