Need help?Do you have a question about the Omron ns series and is the answer not in the manual?
General| Brand | Omron |
|---|---|
| Model | ns series |
| Category | Touch terminals |
| Language | English |
Defines capitalized terms and abbreviations used in the manual.
Explains symbols used for locating information within the manual.
Describes installation and hardware for NS-V1/V2-series PTs.
Provides information on NS Series PTs prior to V1.
Describes screen configurations, object functions, and host communications.
Describes screen creation and transfer between CX-Designer and PT.
Defines NS-series Programmable Terminal.
Indicates OMRON NS products.
Defines Programmable Controller.
Lists OMRON SYSMAC CS/CJ Series Programmable Controllers.
Defines OMRON CX-Designer.
Defines control device interfaced with NS-series PT.
Indicates the NS Series Programming Manual.
Lists personnel qualified to use this manual, requiring electrical systems knowledge.
Advises reading and keeping the manual handy for installation and operation.
States OMRON's warranty for defects in materials and workmanship.
Outlines OMRON's responsibility limits for damages and claims.
Discusses product conformity to standards and provides application examples.
States OMRON is not responsible for user programming of products.
Notes product specifications may change without notice due to improvements.
States dimensions and weights are nominal and not for manufacturing.
Clarifies performance data is a guide and not a warranty.
States no responsibility is assumed for errors or omissions in the manual.
Explains the meaning of WARNING and CAUTION notations.
Explains general prohibition and caution symbols used in the manual.
Provides detailed instructions for safe operation, handling, and environment.
Lists unsuitable installation locations and environments requiring countermeasures.
Introduces the Ladder Monitor application and its monitoring capabilities.
Lists key functionalities like ladder display, PLC monitoring, and search options.
Details new functions introduced in Ladder Monitor version 2.0.
Details new functions introduced in Ladder Monitor version 2.7.
Details new functions introduced in Ladder Monitor version 2.8.
Details new functions introduced in Ladder Monitor version 2.9.
Details new functions introduced in Ladder Monitor version 3.0.
Details new functions introduced in Ladder Monitor version 3.1.
Details new functions introduced in Ladder Monitor version 3.2.
Lists software files provided on the CX-Designer CD-ROM and their usage.
Lists recommended memory card models, capacities, and types for Ladder Monitor.
Details supported PLC types and applicable NS-series PT ports for communication.
Covers communication modes between PLC and PT and startup methods.
Describes limitations for program section display, including rows, columns, and TR bits.
Explains how I/O comments are displayed and their character limits.
Details search capabilities and multiple I/O monitor points.
Covers changing present values and capturing monitor screens.
Shows how display row/column counts vary based on I/O comments and Multiple I/O Monitor usage.
Details the configuration flow for older NS-series PTs requiring a Memory Card.
Outlines the configuration for newer NS-series PTs where Ladder Monitor is built-in.
Describes the configuration process for NSJ Controllers.
Lists other OMRON manuals related to the system.
Details preparing a Memory Card and copying necessary Ladder Monitor application files.
Explains three ways to start the Ladder Monitor: System Menu, User Screen, or Alarm/Event History.
Details using $SW0 or a multifunction object to start the Ladder Monitor from a user screen.
Explains accessing the PT System Menu and PT Settings to start the monitor.
Describes enabling the feature in PT Settings to start Ladder Monitor from alarm events.
Explains reading I/O comments from PLC symbol tables or extracted files.
Details selecting the serial port for PLC monitoring.
Details selecting Ethernet or Controller Link for PLC monitoring.
Details host setup when using the Ladder Monitor for NSJ controllers.
Explains the steps to properly close the Ladder Monitor application.
Describes the main ladder display area and row/column counts based on settings.
Covers section breaks, block programming, and function block display.
Explains the area for monitoring multiple I/O points and their present values.
Details how I/O comments and error messages are displayed.
Describes the function of each button on the Ladder Monitor screen.
Details the process and controls for inputting addresses and numbers in dialog boxes.
Provides a quick lookup for various search operations and corresponding page numbers.
Offers quick reference for displaying program sections and navigating them.
Provides a quick lookup for displaying and managing I/O comments.
Quick reference for monitoring I/O, changing values, modes, and handling errors.
Explains the search process, including timeout settings and cancellation.
Details how to search for specific step numbers in the ladder program.
Explains how to search for specific I/O addresses.
Details searching for output instructions based on specified addresses.
Explains how to search for specific instructions within the program.
Details finding addresses based on the current cursor position.
Explains finding output instructions related to input bits.
Details finding input bits related to output instructions.
Covers returning to previous search results and moving between program sections.
Explains how to scroll through program lines when they exceed screen capacity.
Details starting Ladder Monitor from Alarm/Event Summary to find alarm-related addresses.
Continues explaining how to jump to alarm locations from user screens.
Provides further details on alarm jumps and address search behavior.
Details the procedure for tracing back program execution to find the cause of an output issue.
Explains how to configure the search range and timeout parameters for searches.
Details the procedure for setting the search timeout watch time.
Explains two methods: reading from PLC symbol table or using extracted files.
Details how to switch I/O comment display to three lines, one line, or none.
Explains how to view the full I/O comment text for an instruction or operand.
Explains how bit status and special instruction operand values are displayed.
Provides procedures to stop and restart I/O status monitoring.
Details how to switch present value display between hexadecimal, decimal, and signed decimal.
Details the procedure for adding I/O addresses to the Multiple I/O Monitor.
Covers adding, deleting, changing values, and exiting the Multiple I/O Monitor.
Explains how to force bits ON/OFF or set/reset them using the Ladder Monitor.
Details methods to cancel forced status for all addresses from dialog boxes.
Explains how to check forced bits and cancel them in batches.
Explains the procedure to change the present value of a selected word.
Details changing timer/counter set values specified by constants.
Explains how to change timer/counter values specified by an address.
Details how to change the PLC operating mode to PROGRAM, MONITOR, or RUN.
Lists fatal and non-fatal PLC errors in order of priority.
Provides procedures for clearing individual or all PLC errors.
Details how to capture screens and save them as BMP files on a Memory Card.
Explains the procedure to safely remove the Memory Card from the PT.
Lists PLC CPU units and communication ports that support the Programming Console function.
Details the steps to start the Programming Console function.
Explains the operation of the console screen, including mode selection keys.
Describes how to enable or disable the Programming Console startup option.
Details the process of selecting the host PLC to be monitored by the Ladder Monitor.
Explains how to set up password protection for various sensitive operations.
Shows an example of inputting a password on the PT screen to change operating mode.
Lists causes and countermeasures for the Ladder Monitor failing to start.
Lists FINS command errors and system file errors with their probable causes and countermeasures.
Continues listing FINS command and system file errors and their solutions.
Lists errors related to operation, input, and program section display.
Continues listing operation, input, and other error messages and their solutions.
Lists errors encountered when using the Programming Console function.
Compares ladder program display features between NS Series and CX-Programmer.
Compares features for monitoring I/O status.
Compares the capabilities of the search program section function.
Compares the functionality of the Multiple I/O Monitor feature.
Lists standard NS-series PT models.
Lists supported PLC types, including CS/CJ and NSJ series.
Lists compatible memory card models and capacities.
Explains that the tool extracts I/O comments from CX-Programmer CXT files.
Lists restrictions on CXT file versions, PLC types, and extractable data.
Shows the configuration flow for older NS-series PTs using the tool.
Shows the configuration flow for newer NS-series PTs and NSJ PLCs.
Outlines steps to use the tool, including Memory Card and direct PT transfer.
Details how to select hosts, I/O comment files, and display comments.
Lists computer, OS, memory, and disk requirements, plus setup disk info.
Provides a step-by-step guide for installing the I/O Comment Extracting Tool.
Explains how to launch the I/O Comment Extracting Tool from the Start menu.
Describes the procedure to close the I/O Comment Extracting Tool.
Details the first step of selecting the CXT file for I/O comment extraction.
Covers selecting the PLC and specifying the destination file name for output.
Confirms extraction progress and completion, noting output file types.
Explains how to copy the extracted I/O comment file to a Memory Card or the PT.
Provides a step-by-step guide to uninstall the I/O Comment Extracting Tool.
Lists system global symbols, their I/O comments, and addresses.
To Next Page
