Omron NX102 series User Manual

9
NJ/NX-series CPU Unit Built-in EtherCAT Port User’s Manual (W505)
CONTENTS
1-5-2 Details....................................................................................................................................... 1-15
Section 2 Part Names and Slave Settings
2-1 Part Names and Functions .....................................................................................................2-2
2-1-1 Built-in EtherCAT Port Indicators ................................................................................................ 2-2
2-1-2 Windows Used in Sysmac Studio............................................................................................... 2-4
2-1-3 Connecting the Sysmac Studio................................................................................................... 2-7
2-2 Setting the Node Addresses of the EtherCAT Slaves .......................................................... 2-9
2-3 Features of Sysmac Devices ................................................................................................ 2-12
2-3-1 Sysmac Devices ....................................................................................................................... 2-12
2-3-2 Sysmac Device Features.......................................................................................................... 2-12
2-3-3 List of Sysmac Devices............................................................................................................. 2-15
2-3-4 Sysmac Device Features and EtherCAT Masters .................................................................... 2-16
Section 3 EtherCAT Communications
3-1 EtherCAT Communications Types and Settings .................................................................. 3-2
3-1-1 CoE (CAN Application Protocol over EtherCAT)......................................................................... 3-2
3-1-2 Types of Communications .......................................................................................................... 3-5
3-1-3 Types of EtherCAT Variables...................................................................................................... 3-6
3-1-4 Settings Required for EtherCAT Communications...................................................................... 3-7
3-2 Programming EtherCAT Communications............................................................................ 3-8
3-3 State Transitions for EtherCAT Communications ................................................................ 3-9
3-3-1 Self Diagnosis at Startup ............................................................................................................ 3-9
3-3-2 Control States for EtherCAT Communications ........................................................................... 3-9
3-3-3 CPU Unit Status in Relation to EtherCAT ..................................................................................3-11
Section 4 EtherCAT Network Wiring
4-1 Laying the EtherCAT Network ................................................................................................ 4-2
4-1-1 Supported Network Topologies................................................................................................... 4-2
4-1-2 Installation Precautions............................................................................................................... 4-4
4-1-3 Installing EtherCAT Communications Cables ............................................................................. 4-4
4-1-4 Connecting Communications Cables.......................................................................................... 4-8
4-1-5 Cable Connection Procedure...................................................................................................... 4-9
Section 5 Setting Up EtherCAT Communications with
the Sysmac Studio
5-1 Overview of Network Configuration Information.................................................................. 5-2
5-2 Creating the EtherCAT Network Configuration..................................................................... 5-3
5-3 Setting EtherCAT Slave Variables and Axes ......................................................................... 5-6
5-3-1 Registering Device Variables for All EtherCAT Slaves................................................................ 5-6
5-3-2 Axis Settings for Servo Drives and Encoder Input Slaves ........................................................ 5-10
5-4 EtherCAT Master and Slave Parameter Settings ................................................................ 5-11
5-4-1 Setting EtherCAT Master ...........................................................................................................5-11
5-4-2 Setting EtherCAT Slaves .......................................................................................................... 5-16
5-5 Comparing and Merging EtherCAT Network Configurations ............................................ 5-24
5-5-1 Comparing and Merging with the Actual Network Configuration from the Sysmac Studio ....... 5-24
5-5-2 Automatically Creating the Network Configuration ................................................................... 5-29
5-5-3 Using the Sysmac Studio to Obtain Serial Numbers from the Actual
Network Configuration .............................................................................................................. 5-32

Omron NX102 series Specifications

General

Brand	Omron
Model	NX102 series
Category	Controller
Language	English