Oracle Netra SPARC S7-2 Series - Locate Device Paths (Openboot)

Locate Device Paths (OpenBoot)
/SYS/MB/PCIE_SWITCH1/PCIE_LINK4 | current_config_state | Enabled
/SYS/MB/PCIE_SWITCH1/PCIE_LINK5 | current_config_state | Enabled
/SYS/MB/PCIE_SWITCH1/PCIE_LINK6 | current_config_state | Enabled
/SYS/MB/PCIE_SWITCH1/PCIE_LINK7 | current_config_state | Enabled
/SYS/MB/PCIE_SWITCH1/PCIE_LINK8 | current_config_state | Enabled
/SYS/MB/PCIE_SWITCH1/PCIE_LINK12 | current_config_state | Enabled
/SYS/MB/RISER1/PCIE1 | current_config_state | Enabled
/SYS/MB/RISER2/PCIE2 | current_config_state | Enabled
/SYS/MB/RISER3/PCIE3 | current_config_state | Enabled
/SYS/MB/RISER3/PCIE4 | current_config_state | Enabled
/SYS/MB/USB_CTRL | current_config_state | Enabled
/SYS/MB/XGBE | current_config_state | Enabled
->
Related Information
■
“Locate Device Paths (OpenBoot)” on page 73
Locate Device Paths (OpenBoot)
1.
Display the OpenBoot prompt.
See “Obtain the OpenBoot Prompt Under Various Conditions” on page 21.
2.
From the OpenBoot prompt, type:
Note - This document applies to several server products. The following example is based on the
SPARC S7-2 server. Your output might vary from the examples based on your product.
ok devalias
fallback-miniroot /pci@300/pci@1/pci@0/pci@2/usb@0/hub@2/storage@1/disk@0
rcdrom /pci@300/pci@1/pci@0/pci@2/usb@0/hub@2/storage@1/disk@0
disk7 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p4
disk6 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p5
disk5 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p7
disk4 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p6
disk3 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p0
disk2 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p1
disk1 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p3
disk /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p2
disk0 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0/disk@p2
sas0 /pci@302/pci@2/pci@0/pci@14/LSI,sas@0
sas /pci@302/pci@2/pci@0/pci@14/LSI,sas@0
nvme3 /pci@302/pci@2/pci@0/pci@7/nvme@0/disk@1
Matching Devices to Device Names 73