Panasonic AW-HE130W - Page 74

Internet mode (over HTTP)
ThissettingisselectedwhentransmittingH.264imagesoverthe
Internet.
H.264imagescanbetransmittedusingthesamebroadbandrouter
settingsaswhentransmittingJPEGimages.
Setting value:
On TheH.264imagesandaudioaretransmittedusingtheHTTP
port.FordetailsonsettingtheHTTPportnumber,referto
page@@.
Off TheH.264images and audioaretransmitted using theUDP
port.
Factory settings: Off
<NOTE>
• When“On”isset,only“Unicastport(Portnumbersettings:AUTO)”
canbeselectedasthe“Transmissiontype”setting.
• When“On”isset,ittakesafewsecondsbeforetheH.264images
aredisplayed.
• Whenthisissetto[On],H.264imagesmaynotappeardepending
onthenumberofusersaccessingtheunitatthesametimeand
whetheraudiodataexists.
• Whenthisthissetto[On],accesswillbelimitedtoIPv4.
Image capture size
SelecttheresolutionforH.264images.
Selectableoptionswillvarydependingontheselectedresolution
setting.
Setting value:
H264(1) 1920×1080
1280×720
H264(2) 1920×1080
1280×720
640×360
320×180
160×90
H264(3) 1280×720
640×360
320×180
160×90
H264(4) 1280×720
640×360
320×180
160×90
Factory settings:
H.264(1):1920×1080
H.264(2):640×360
H.264(3):320×180
H.264(4):160×90
Transmission priority
SetthetransmissionmodeforH.264images.
Setting value:
Constantbitrate TransmitsH.264imagesatthebitratespecified
in[Maxbitrate(perclient)].
Framerate TransmitH.264imagesattheframeratespecified
in[Framerate].
Besteffort Transmit H.264 images at a variable bit rate
betweenthe maximumandminimumspecifiedin
[Maxbitrate(perclient)],accordingtothenetwork
bandwidth.
AdvancedVBR TransmitH.264imagesattheframeratespecified
in [Framerate]. Images will be transmitted so
that the average transmission volume during the
duration specified in [Control time period] will be
thebitratespecifiedin[Maxbitrate(perclient)].
Factory settings: Framerate
<NOTE>
• When[Transmissionpriority]issetto[Framerate]or[Advanced
VBR],thenumberofusersthatcanconnectmaydecrease.
Framerate
SettheframerateforH.264images.
Setting value:
For 60Hz:
5fps
*
1
/15fps
*
1
/30fps
*
1
/60fps
*
1
For 50Hz:
5fps
*
1
/12.5fps
*
1
/25fps
*
1
/50fps
*
1
Factory settings:
For 60Hz: 30fps
For 50Hz: 25fps
*
1
Theframerateislimitedbythe[Maxbitrate(perclient)]setting.
Theactualframeratemaybelowerthanthespecifiedvalue.
<NOTE>
• Thissettingisonlyenabledwhen[Transmissionpriority]issetto
[Framerate]or[AdvancedVBR].
• [H.264(1)]isfixedat60fps(for60Hz)and50fps(for50Hz).
60fps(for60Hz)and50fps(for50Hz)cannotbeselectedfor
[H.264(2)]to[H.264(4)].
Burst tolerance level
Selecthowmuchmorethanthe[Maxbitrate(perclient)]valueto
allowfortheH.264bitrate.
Setting value:
High/Middle/Low
Factory settings: Low
<NOTE>
• Thissettingisonlyenabledwhen[Transmissionpriority]issetto
[AdvancedVBR].
Control time period
SelectthedurationforwhichtheH.264bitratewillbecontrolled.
Imageswillbetransmittedsothattheaveragetransmissionvolume
duringthedurationspecifiedwillbethebitratespecifiedin[Maxbit
rate(perclient)].
Setting value:
1h 1hours
6h 6hours
24h 1day(24hours)
1week 1week
Factory settings: 24h
<NOTE>
• Thissettingisonlyenabledwhen[Transmissionpriority]issetto
[AdvancedVBR].
74
Web screen configurations (continued)
75