Panasonic AW-HE130W - Page 75

Max bit rate (per client)
SpecifytheH.264bitrateperclient.
When[Transmissionpriority]issetto[Besteffort],specifythe
maximumandminimumbutrate.
Setting value:
64kbps/128kbps
*
1
/256kbps
*
1
/384kbps
*
1
/512kbps
*
1
/
768kbps
*
1
/1024kbps
*
1
/1536kbps
*
1
/2048kbps
*
1
/3072kbps
*
1
/
4096kbps
*
1
/6144kbps
*
1
/8192kbps
*
1
/10240kbps
*
1
/
12288kbps
*
1
/14336kbps
*
1
/16384kbps
*
1
/20480kbps
*
1
/
24576kbps
*
1
Factory settings:
H.264(1):4096kbps
H.264(2):1536kbps
H.264(3):1024kbps
H.264(4):512kbps
TherangeofH.264bitratesthatcanbespecifiedvariesdepending
ontheresolution.
• 160×90:64kbpsto2048kbps
• 320×180,640×360:64kbpsto4096kbps
• 1280×720:256kbpsto8192kbps
• 1920×1080:512kbpsto14336kbps
• 1920×1080(60fps),1280×720(60fps):
1024kbpsto24576kbps
*
1
TheH.264bitrateislimitedbythe[Bandwidthcontrol(bitrate)]
(→page@@)settingunderthe[Network]taboftheNetwork
screen.Theactualbitratemaybelowerthanthespecifiedvalue.
Image quality
SelecttheimagequalityforH.264images.
Setting value:
Low(Motionpriority)/Normal/Fine(Imagequalitypriority)
Factory settings: Normal
<NOTE>
• Thissettingisonlyenabledwhen[Transmissionpriority](→page
@@)issetto[Constantbitrate]or[Besteffort].
Refresh interval
SelecttherefreshintervalforH.264images(I-frameinterval:0.2to5
seconds).
Iferrorsoccurfrequentlyinthenetworkenvironment,decreasingthe
refreshintervalwillreduceimagedistortions.
However,theframeratemaydecrease.
Setting value:
For 60Hz:
0.2s/0.25s/0.33s/0.5s/1s/2s/3s/4s/5s
For 50Hz:
0.2s/0.5s/1s/2s/3s/4s/5s
Factory settings: 1s
Transmission type
SelectthetransmissionformatforH.264images.
Setting value:
Unicastport
(AUTO)
Upto24userscanaccessasinglecameraatthe
sametime.
[Unicastport1(Image)]and[Unicastport2
(Audio)]willbeconfiguredautomaticallywhen
imagesandaudioaresentfromthecamera.
Werecommendselectingthe[Unicastport
(MANUAL)]settingwhentheportnumber
transmittingtheH.264imagesdoesnotneedto
befixed(e.g.,duringusewithinanetwork).
Unicastport
(MANUAL)
Upto24userscanaccessasinglecameraatthe
sametime.
[Unicastport1(Image)]and[Unicastport2
(Audio)]mustbeconfiguredmanuallywhen
imagesandaudioaresentfromthecamera.
WhentransmittingH.264imagesviathe
Internet,configureafixedtransmissionportfor
thebroadbandrouter(hereafterreferredtoas
"router")(→page@@).Fordetails,refertothe
operatinginstructionsfortherouter.
Multicastport Anunlimitednumberofuserscanaccessasingle
cameraatthesametime.
WhentransmittingH.264imagesviamulticast,
enterthe[Multicastaddress],[Multicastport],and
[MulticastTTL/HOPLimit].
Factory settings: Unicastport(AUTO)
<NOTE>
• Fordetailsonthemaximumnumberforsimultaneousaccess,see
page@@.
Unicast port1 (Image)
*
1
Entertheunicastportnumber(usedwhensendingimagesfromthe
unit).
Usable port number range: 1024to50000
• Onlyevennumberscanbespecified.
• Theportnumbercannotbesetto10670.
Factory settings:
H.264(1):32004
H.264(2):32014
H.264(3):32024
H.264(4):32034
*
1
Theunicastportnumbermustbeconfiguredwhen[Transmission
type]issetto[Unicastport(MANUAL)].

Unicast port2 (Audio)
*
1
Usable port number range: 1024to50000
• Onlyevennumberscanbespecified.
• Theportnumbercannotbesetto10670.
Factory settings:
H.264(1):32004
H.264(2):32014
H.264(3):32024
H.264(4):32034
*
1
Theunicastportnumbermustbeconfiguredwhen[Transmission
type]issetto[Unicastport(MANUAL)].
74
75
Web screen configurations (continued)