82
VQT2J52
Troubleshooting guide
On-screen display indicators do not appear.
¾ Select a setting other than “Off” in “On-Screen Messages” in the
Setup Menu. (> 65)
– Press [STATUS ] to show the on-screen display indicators.
– The on-screen indicator for video cassette playback will not
be displayed when this unit is connected to the TV with the
DVD priority out terminals.
The grey background appears during playback.
¾ You are playing a blank or poor quality portion of the tape.
¾ You can damage the unit if you play dirty or damaged tapes and
this can cause the grey background to appear.
Cannot hear the desired audio type.
¾ Press [AUDIO] to select the audio. (> 37)
There is noise when playing a video tape.
¾ Adjust the tracking. (> 37)
¾ The tape is old or damaged.
The playback screen flickers.
¾ The video head is dirty. (> 5)
¾ The tape is old or damaged.
¾ Check the “SQPB” setting. (> 67)
“1” flashes when I try to start recording.
Cannot record.
¾ A video cassette is not inserted. Insert a video cassette with an
accidental erasure prevention tab. (> 5)
¾ The accidental erasure prevention tab has been removed.
Cover the hole with adhesive tape. (> 5)
The contents of the USB memory cannot be read.
¾ Remove the USB memory from the USB port and then insert
again. If this does not solve the problem, turn off and turn on the
unit again.
¾ Check that the USB memory is inserted correctly. (> 15)
¾ The format of the USB memory or of its contents is not
compatible with the unit. (The contents on the USB memory
may be damaged.) (> 13, 14)
¾ The USB memory contains a folder structure and/or file
extensions that are not compatible with this unit. (> 14)
¾ Turn off and then turn on the unit again.
¾ USB memories connected using a USB extension cable or a
USB hub may not be recognized by this unit.
¾ Some USB memories cannot be used with this unit. (> 13)
¾ If inserted during playback, recording or copying etc., the USB
memory may not be recognized by this unit.
The TV Guide System does not receive any data.
¾ Check whether TV Guide system setup was performed in full.
¾ Check whether the clock is properly set. (> 67)
¾ If signal quality is bad (ghost images or limited reception), the
TV Guide system may not be able to receive any data.
¾ In the area where GUIDE Plus+ system is available, check
whether correct post code is entered. (> 68)
“No Data” is displayed for some or all stations.
¾ Some stations are not supported by the TV Guide system.
¾ Analogue broadcasts are not supported by the TV Guide
system.
¾ Programme the Timer recording manually or via S
HOWVIEW
([For]Germany[and]Austria[). (> 30)
The TV Guide information is not displayed
properly.
¾ There was a programme change.
Check the current programme, e.g. on the Web site for the TV
Guide system provider or station provider.
¾ Programme information about analogue broadcasts is not
displayed.
The TV Guide data transfer was interrupted.
¾ The TV Guide system shows the data that was received up to
the interruption.
¾ The programme information may be incomplete.
The TV Guide data is not updated.
¾ The unit must be in standby mode in order to update the data. If
the unit is in EXT LINK mode (EXT-L lights up in the display),
then the data update may also not work.
¾ Make sure that the time is set correctly.
¾ Make sure that “TV Guide Download in Standby” is set to “On”.
(> 68)
VHS
USB
TV Guide
DMR-EZ49VEGEC-VQT2J52_eng.book 82 ページ ２０１０年１月７日 木曜日 午後４時０分
To Next Page
Loading...
