Panasonic HEVC Advance AW-UE160WP - Page 123

HDMI
Make the settings for output from the HDMI connector.
Format Select
Set the output format.
The following formats can be set depending on the settings in
[Format] in [Basic Config].
Frequency System Format Format (HDMI)
60Hz 2160/60p 2160/60p
1080/60p
1080/60p 1080/60p
59.94Hz 2160/59.94p 2160/59.94p
1080/59.94p
*
1
2160/29.97p 2160/29.97p
1080/29.97p
1080/119.88p 1080/119.88p
1080/59.94p 1080/59.94p
1080/59.94i
1080/29.97p 1080/29.97p
720/59.94p 720/59.94p
50Hz 2160/50p 2160/50p
1080/50p
*
2
2160/25p 2160/25p
1080/25p
1080/100p 1080/100p
1080/50p 1080/50p
1080/50i
1080/25p 1080/25p
720/50p 720/50p
24Hz 2160/24p 2160/24p
1080/24p
1080/24p 1080/24p
23.98Hz 2160/23.98p 2160/23.98p
1080/23.98p
1080/23.98p 1080/23.98p
*
1
When [UHD Crop] is [Crop(720)], output is 720/59.94p.
*
2
When [UHD Crop] is [Crop(720)], output is 720/50p.
Factory settings: 2160/59.94p or 2160/50p
HDR OUTPUT SELECT
[SDR(709), HDR(709), HDR(2020)]
Select the signal output when [HDR] is [On].
SDR(709) Selects the SDR output signal.
HDR(709) Selects the HDR output signal (BT.709 equivalent color
gamut).
HDR(2020) Selects the HDR output signal (BT.2020 equivalent color
gamut).
Factory settings: HDR(2020)
<NOTE>
• This cannot be set when the [Basic Config] – [HDR] is [Off].
• [HDR(2020)] can be selected only when [Basic Config] – [GAMUT]
is [WIDE_G2].
V-LOG OUTPUT SELECT [V-LOG, V-709]
Select the signal output when [V-LOG] is [On].
V-LOG Output with a gamma curve that has a wide range of
tones and latitude (exposure range).
V-709 Converted for output to images suited to previewing.
Factory settings: V-LOG
<NOTE>
• This cannot be set when the [Basic Config] – [V-LOG] is [Off].
Video Sampling [4:2:2/10bit, 4:2:0/8bit]
When [Format Select] in [HDMI] is [2160/59.94p], [2160/60p]
or [2160/50p], select the video sampling output from the HDMI
connector.
Factory settings: 4:2:2/10bit
<NOTE>
• When [Format Select] in [HDMI] is other than [2160/59.94p],
[2160/60p] or [2160/50p], [Video Sampling] cannot be changed and
is fixed at [4:2:2/10bit].
CHAR [Off, On]
Set whether to superimpose the OSD.
Factory settings: On
z Return
RETURN1 ID
You can give a name to the return images (SMPTE ST2110 input
images).
It can be 5 characters.
Alphanumeric characters, spaces, ! # % & ' ( )
*
+ , - . / : ; < = > ? [ ]
_
~
$ @ |
The setting is confirmed with the [Set] button.
The name you set is superimposed on the images output from
the same connector when [RETURN] is selected in [OUTPUT] –
[3G SDI OUT2/PM] – [OUTPUT SELECT].
<NOTE>
• This item cannot be set if the SMPTE ST2110 software key (AW-
SFU60) is disabled.
123
Web screen configurations (continued)