CHAR [OFF, ON]
Set whether to superimpose the OSD.
<NOTE>
• During IP video transmission (H.264/H.265/M-JPEG), there may
be some delays in OSD menu operations. Smooth OSD menu
operations become possible when you set this item to [OFF].
ST2110
Make a variety of settings and display changes related to the SMPTE
ST2110 images.
<NOTE>
• This item cannot be set if the SMPTE ST2110 software key
(AW-SFU60) is disabled.
• This cannot be set when the [BASIC CONFIG] – [SFP+ MODE] is
[12G OUTPUT].
MOIP MODE [OFF, ON]
Set OFF/ON for MOIP (SMPTE ST2110 video/audio input/output).
MAIN VIDEO TX
FORMAT
Set the image format of the MAIN video signal of SMPTE ST2110.
Frequency
System Format Format (ST2110)
59.94Hz 1080/59.94p 1080/59.94p
1080/59.94i
50Hz 1080/50p 1080/50p
1080/50i
For formats other than the above, there is display only and the
settings cannot be changed.
<NOTE>
• Camera images without overlays such as OSD menus and CROP
frames are output from MAIN VIDEO TX.
• When [MOIP MODE] is [OFF], MAIN VIDEO TX is not output. The
image format is also not displayed.
CROP VIDEO TX
FORMAT
Display the image format of the CROP video signal of SMPTE
ST2110.
<NOTE>
• Camera images without overlays such as OSD menus are output
from CROP VIDEO TX.
• When [MOIP MODE] is [OFF] and [UHD CROP] is set to [OFF],
CROP VIDEO TX is not output. The image format is also not
displayed.
MONITOR VIDEO TX
FORMAT
Display the image format of the monitor video signal of SMPTE
ST2110.
<NOTE>
• The OSD menu display with images output from MONITOR
VIDEO TX of ST2110 is linked to the settings made in [OUTPUT]
– [3G SDI OUT2/PM] – [CHAR] and [OUTPUT ITEM].
• When [MOIP MODE] is [OFF] and [OUTPUT] – [3G SDI OUT2/
PM] – [OUTPUT SELECT] is set to [RETURN], MONITOR VIDEO
TX is not output. The image format is also not displayed.
RETURN VIDEO RX
FORMAT
Display the image format of the RETURN video signal of SMPTE
ST2110.
<NOTE>
• RETURN VIDEO RX cannot be input when [MOIP MODE] is [OFF]
and [BASIC CONFIG] – [FORMAT] is other than [1080/59.94p] or
[1080/50p]. The image format is also not displayed.
PAINT
AUTO
Make settings for auto operation.
AGC [OFF, ON]
Set the behavior of auto gain control.
AUTO IRIS [OFF, ON]
Select whether to turn auto iris adjustment OFF/ON.
ATW [OFF, ON]
Set the behavior of the auto tracking white balance function.
AUTO SHUTTER [OFF, ON]
Set the behavior of auto shutter control.
KNEE MODE [AUTO, MANUAL]
Set the operating mode for gradation compression (knee).
GAIN SETTING
The image gain is adjusted here.
GAIN [–6dB to 12dB]
The image gain is adjusted here.
In locations which are too dark, adjust the gain upward; conversely, in
locations which are too bright, adjust it downward.
AGC [OFF, ON]
Set the behavior of auto gain control.
AGC MAX GAIN [6dB, 12dB]
Set the maximum amount of gain increase when [AGC] is working.
FRAME MIX SW [OFF, ON]
Set the control for frame addition (gain increase using sensor
storage).
FRAME MIX [6dB, 12dB, 18dB, 24dB]
Set the frame addition (gain increase using sensor storage) amount.
When frame addition is performed, it will appear as if the images are
missing some frames.
This cannot be configured when the format is 2160/29.97p,
2160/23.98p, 2160/24p, 2160/25p, 1080/29.97p, 1080/23.98p,
1080/24p, 1080/25p, 1080/119.88p or 1080/100p.
<NOTE>
• Under discharge tube illumination, such as fluorescent and
mercury-vapor lights, the brightness may change cyclically, colors
may change, and horizontal stripes may flow up and down the
image.
• When [FRAME MIX] is set to 6dB, 12dB, 18dB or 24dB, if you set
[SHUTTER SW] to [ON], [FRAME MIX SW] is changed to [OFF].
DAY/NIGHT [DAY, NIGHT]
Switch between standard shooting and night-vision shooting (shooting
with infrared light).
DAY Standard shooting (day mode)
NIGHT Night-vision shooting (night mode)
<NOTE>
• In night mode, video output will be in black and white. In addition,
the iris will be forcibly opened.
• White balance adjustment is not possible in night mode.
• ND filter switching is not possible in night mode.
58
Camera menu items (continued)
To Next Page
Loading...
