The CROP function
If [UHD CROP] is set to [CROP(1080)] or [CROP(720)], images cropped
from the UHD signal can be output via the 3G SDI OUT1 connector, the
CROP images of SMPTE ST2110, High bandwidth NDI images, and the
LAN connector (H.264/H.265/M-JPEG). (Image 2)
When this happens, uncropped UHD image video signals that are
down-converted to FHD are output to other connectors that do not have
cropped images, with crop frames displayed according to the menu
settings in [CROP MARKER]. (Image 1)
Crop frame
Image 1 Image 2
Depending on the [3G SDI1 OUT], [NDI OUT], [IP(H.264/H.265) OUT1],
[IP(H.264/H.265) OUT2] and [CROP OUT] settings, images output from
the 3G SDI OUT and LAN connectors will be as shown below.
3G SDI1 OUT /
NDI OUT /
IP(H.264/H.265) OUT1 /
IP(H.264/H.265) OUT2
CROP
OUT
Images output from 3G SDI OUT and
LAN connectors
FULL - UHD images down-converted to FHD
CROP YL Images cropped with the yellow frame
G Images cropped with the green frame
MG Images cropped with the magenta
frame
<NOTE>
• Cropped images cannot be output with the 12G SDI OUT/SFP+
connector, 3G SDI OUT2/PM connector, HDMI connector, SMPTE
ST2110 MAIN images, or SMPTE ST2110 MONITOR images.
Depending on the [CROP MARKER] settings, it is possible to select the
crop frame to output to the 3G SDI OUT1 connector, 3G SDI OUT2/
PM connector, MONITOR images of SMPTE ST2110, and the IP
(H.264/H.265/M-JPEG) connector, with a connector that is not outputting
cropped images.
CROP MARKER Crop frame display
OFF Crop frame is not displayed.
YL Only a yellow crop frame is displayed.
G Only a green crop frame is displayed.
MG Only a magenta crop frame is displayed.
YL+G Yellow and green crop frames are displayed.
YL+MG Yellow and magenta crop frames are displayed.
G+MG Green and magenta crop frames are displayed.
YL+G+MG Yellow, green, and magenta crop frames are
displayed.
<NOTE>
• When moving the CROP frame (YL/G/MG), there may be some jerking
of the CROP frame display, but there will be no jerking in the actual
CROP output images.
• Crop frames cannot be displayed via the 12G SDI OUT/SFP+
connector or HDMI connector, or with SMPTE ST2110 MAIN images
and SMPTE ST2110 CROP images.
PAN/TILT
INSTALL POSITION [DESKTOP, HANGING]
[DESKTOP] or [HANGING] is selected here as the method used to
install the unit.
DESKTOP Stand-alone installation
HANGING Suspended installation
<NOTE>
• When [HANGING] has been selected, the top, bottom, left and right
of the images will be reversed, and up/down/left/right control for
panning and tilting will also be reversed.
SMART PICTURE FLIP [OFF, AUTO]
When the tilt becomes the angle set for [FLIP DETECT ANGLE], the
image will be flipped in the vertical direction automatically.
OFF The picture is not turned upside down.
AUTO The picture is automatically turned upside down.
FLIP DETECT ANGLE [60deg, 120deg]
Set the tilt angle at which the image will be flipped in the vertical
direction automatically when [SMART PICTURE FLIP] is set to
[AUTO].
P/T SPEED MODE
[NORMAL(60deg/s), FAST1(90deg/s), FAST2(180deg/s)]
Set the speed of PAN/TILT operation.
NORMAL(60deg/s) PAN/TILT operates at normal speed (maximum
about 60° per second).
FAST1(90deg/s) PAN/TILT operates at fast speed1 (maximum
about 90° per second).
FAST2(180deg/s) PAN/TILT operates at fast speed2 (maximum
about 180° per second).
P/T ACCELERATION SETTING
Displays the advanced setting screen for setting the acceleration
speed while starting/stopping a pan/tilt operation.
P/T ACCELERATION [MANUAL, AUTO]
Sets whether to perform advance setting for acceleration and
deceleration etc. during manual operation of pan/tilt.
MANUAL Sets the advanced settings for acceleration speed
etc. during start/stop or changing the speed of pan/tilt
operation.
AUTO Sets the settings for automatic acceleration and
deceleration speed etc. during start/stop or changing the
speed of pan/tilt operations.
RISE S-CURVE [0 to 30]
Sets the S-curve for pan/tilt acceleration operation in 31 steps. (The
greater the number, the steeper the S-curve)
When it is necessary to increase the speed to the specified speed
using manual control of pan/tilt by lever operation etc. through the
controller, the acceleration process is performed based on the
S-curve specified in this setting.
This is enabled only when [P/T ACCELERATION] is [MANUAL].
<NOTE>
• In order to limit the acceleration response, in the S-curve step, as
the acceleration speed rises, the limit is automatically applied.
74
Camera menu items (continued)
To Next Page
Loading...
