Panasonic HEVC Advance AW-UE160WP - Ip Signal

OUTPUT SETTING
Display the setting status of audio output.
CH SELECT [INPUT1/INPUT2, INPUT1, INPUT2]
Select the audio output destination.
INPUT1/INPUT2 CH1-INPUT1/CH2-INPUT2
INPUT1 CH1-INPUT1/CH2-INPUT1
INPUT2 CH1-INPUT2/CH2-INPUT2
<NOTE>
• When [CH SELECT] is [INPUT1], the INPUT2 AUDIO TX of ST2110
is not output.
• When [CH SELECT] is [INPUT2], the INPUT1 AUDIO TX of ST2110
is not output.
CH1 VOLUME LEVEL
[–40dB to 0dB to +20dB (1dB step)]
Set the volume for CH1 audio output.
CH2 VOLUME LEVEL
[–40dB to 0dB to +20dB (1dB step)]
Set the volume for CH2 audio output.
HEAD ROOM [FS-12dB, FS-18dB, FS-20dB]
Set the audio head room (base level).
FS-12dB ‒12dBFS
FS-18dB ‒18dBFS
FS-20dB ‒20dBFS
ST2110 AUDIO FORMAT
INPUT1 [1ms/8ch, 0.125ms/8ch]
Set the format for AUDIO (INPUT1) of SMPTE ST2110.
INPUT2 [1ms/8ch, 0.125ms/8ch]
Set the format for AUDIO (INPUT2) of SMPTE ST2110.
<NOTE>
• This item cannot be set if the SMPTE ST2110 software key
(AW-SFU60) is disabled.
• This cannot be set when the [BASIC CONFIG] – [SFP+ MODE] is
[12G OUTPUT].
IP SIGNAL
NDI
Make a variety of settings related to High bandwidth NDI images.
FORMAT SELECT
Set the output format.
Frequency System Format Format (NDI)
60Hz 2160/60p 2160/60p
*
9
1080/60p
1080/60p 1080/60p
59.94Hz 2160/59.94p 2160/59.94p
*
1, 2
1080/59.94p
2160/29.97p 2160/29.97p
*
3
1080/29.97p
1080/119.88p 1080/59.94p
*
10
1080/59.94p 1080/59.94p
1080/29.97p 1080/29.97p
720/59.94p 720/59.94p
50Hz 2160/50p 2160/50p
*
4, 5
1080/50p
2160/25p 2160/25p
*
6
1080/25p
1080/100p 1080/50p
*
10
1080/50p 1080/50p
1080/25p 1080/25p
720/50p 720/50p
24Hz 2160/24p 2160/24p
*
7
1080/24p
1080/24p 1080/24p
23.98Hz 2160/23.98p 2160/23.98p
*
8
1080/23.98p
1080/23.98p 1080/23.98p
*
1
When [UHD CROP] is [CROP(1080)], output is 1080/59.94p.
*
2
When [UHD CROP] is [CROP(720)], output is 720/59.94p.
*
3
When [UHD CROP] is [CROP(1080)], output is 1080/29.97p.
*
4
When [UHD CROP] is [CROP(1080)], output is 1080/50p.
*
5
When [UHD CROP] is [CROP(720)], output is 720/50p.
*
6
When [UHD CROP] is [CROP(1080)], output is 1080/25p.
*
7
When [UHD CROP] is [CROP(1080)], output is 1080/24p.
*
8
When [UHD CROP] is [CROP(1080)], output is 1080/23.98p.
*
9
When [UHD CROP] is [CROP(1080)], output is 1080/60p.
*
10
For 119.88p (or 100p), “Frame 1” is output with the frame rate cut
to half (59.94p (or 50p)).
<NOTE>
• OSD menus are not displayed in the output video from High
bandwidth NDI.
IP(H.264/H.265)
Make a variety of settings related to IP video transmission (H.264/
H.265/M-JPEG).
OUTPUT ITEM [MENU ONLY, STATUS]
Select the type of OSD to be superimposed on output video.
MENU ONLY Displays the OSD menu only.
STATUS Displays the OSD menu and OSD status.
57
Camera menu items (continued)