Panasonic HEVC Advance AW-UE160WP - RGB Gain Control and Flare Compensation; Noise Reduction (DNR) and V-LOG DNR

z RGB GAIN CONTROL SETTING
<NOTE>
• For all of the RGB GAIN CONTROL SETTING items, setting is not
possible when [V-LOG] is [On] and [V-LOG PAINT SW] is [Off].
G GAIN REL CONTROL SWITCH [Off, On]
Set On/Off for the relative value control of the G gain.
Factory settings: Off
RGB GAIN PRESET
Set the gain when the [WHITE BALANCE MODE] is [3200K], [5600K],
or [VAR].
R GAIN [–1000 to +1000]
This enables the R gain to be adjusted.
Factory settings: 0
G GAIN [–1000 to +1000]
This enables the G gain to be adjusted.
Factory settings: 0
B GAIN [–1000 to +1000]
This enables the B gain to be adjusted.
Factory settings: 0
RGB GAIN ACH/BCH
Set the gain when the [WHITE BALANCE MODE] is [AWB A] or
[AWB B].
ACH
R GAIN ACH [–1000 to +1000]
You can adjust the R gain when the [WHITE BALANCE MODE] is
[AWB A].
Factory settings: 0
B GAIN ACH [–1000 to +1000]
You can adjust the B gain when the [WHITE BALANCE MODE] is
[AWB A].
Factory settings: 0
G GAIN ACH [–1000 to +1000]
You can adjust the G gain when the [WHITE BALANCE MODE] is
[AWB A].
Factory settings: 0
GAIN OFFSET ACH [Off, On]
When auto white balance is performed by setting [WHITE
BALANCE MODE] to [AWB A], set the values for R gain and B gain.
Off Makes the [R GAIN ACH] and [B GAIN ACH] values [0].
On Leaves the values set in [R GAIN ACH] and [B GAIN
ACH] as they are.
Factory settings: Off
BCH
R GAIN BCH [–1000 to +1000]
You can adjust the R gain when the [WHITE BALANCE MODE] is
[AWB B].
Factory settings: 0
B GAIN BCH [–1000 to +1000]
You can adjust the B gain when the [WHITE BALANCE MODE] is
[AWB B].
Factory settings: 0
G GAIN BCH [–1000 to +1000]
You can adjust the G gain when the [WHITE BALANCE MODE] is
[AWB B].
Factory settings: 0
GAIN OFFSET BCH [Off, On]
When auto white balance is performed by setting [WHITE
BALANCE MODE] to [AWB B], set the values for R gain and B gain.
Off Makes the [R GAIN BCH] and [B GAIN BCH] values [0].
On Leaves the values set in [R GAIN BCH] and [B GAIN
BCH] as they are.
Factory settings: Off
z FLARE
<NOTE>
• For all of the FLARE items, setting is not possible when [V-LOG] is
[On] and [V-LOG PAINT SW] is [Off].
FLARE [Off, On]
Set Off/On for flare compensation.
Factory settings: Off
MASTER FLARE [–200 to 0 to +200]
Adjust the master flare.
Factory settings: 0
R FLARE [–200 to 0 to +200]
Adjust the Rch flare.
Factory settings: 0
G FLARE [–200 to 0 to +200]
Adjust the Gch flare.
Factory settings: 0
B FLARE [–200 to 0 to +200]
Adjust the Bch flare.
Factory settings: 0
DNR / V‑LOG DNR
<NOTE>
• For all of the DNR / V-LOG DNR items, setting is not possible when
[V-LOG] is [On] and [V-LOG PAINT SW] is [Off].
DNR SW [OFF, ON]
Select OFF/ON for the digital noise reduction effect which can
achieve output of bright, clear images without noise, even at night and
low-light conditions.
Factory settings: OFF
DNR LEVEL [1 to 5]
Set the digital noise reduction level.
Factory settings: 3
147
Web screen configurations (continued)