GAMUT [NORMAL, WIDE_G2]
Set the color gamut.
NORMAL BT.709 equivalent color gamut.
WIDE_G2 BT.2020 equivalent color gamut.
<NOTE>
• This cannot be set when the [BASIC CONFIG] – [HDR] is [OFF].
SHOOTING MODE [NORMAL, LOW LIGHT]
Select the shooting mode to suit the shooting environment.
NORMAL Select this when shooting in an environment with normal
brightness.
LOW LIGHT Select this for high sensitivity shooting. (Suited to
shooting in dark environments.)
<NOTE>
• The black level may vary when [LOW LIGHT] is selected, but this
does not indicate a problem with camera performance.
SERIAL CONNECTION
BAUD RATE [9600bps, 38400bps, 115200bps]
Set the communication speed (baud rate) for the RS-422 connector.
<NOTE>
• This item is disabled when [TRACKING DATA OUTPUT] –
[SERIAL] is [ON].
BAR [OFF, ON]
OFF Outputs camera images.
ON Outputs the color bar.
COLOR BAR TYPE [TYPE1, TYPE2, TYPE3, TYPE4, TYPE5]
Select the type of color bar to display.
COLOR BAR TYPE
Output color bar
IP
transmissions
(H.264/H.265/
M-JPEG)
SDI/HDMI
or
SMPTE ST2110/
High bandwidth NDI
HD (720
or 1080)
UHD
(2160)
TYPE1 SMPTE
TYPE1 SDI/HDMI
TYPE1 TYPE1
SMPTE ST2110/
High bandwidth NDI
TYPE1 TYPE1
TYPE2 FULL
TYPE2 SDI/HDMI
TYPE2 TYPE2
SMPTE ST2110/
High bandwidth NDI
TYPE2 TYPE2
TYPE3 ARIB(FHD)
TYPE1 SDI/HDMI
TYPE3 TYPE3
SMPTE ST2110/
High bandwidth NDI
TYPE3 TYPE3
TYPE4 ARIB(UHD)
TYPE1 SDI/HDMI
TYPE3 TYPE4
SMPTE ST2110/
High bandwidth NDI
TYPE3 TYPE3
TYPE5 ARIB(2020/HLG)
TYPE1 SDI/HDMI
TYPE3 TYPE5
SMPTE ST2110/
High bandwidth NDI
TYPE3 TYPE3
<NOTE>
• When [BAR] is [ON], the color bars of the various HDR/GAMUT/
V-LOG setting screens are output as color bars with [HDR] [OFF]/
[V-LOG] [OFF].
• Color bars of IP transmissions (H.264/H.265/M-JPEG) do not
conform with SMPTE.
• BAR ID (→ page 50) is not output with [TYPE4]/[TYPE5].
• With [TYPE4], 2020 is output even when set to 709.
• TYPE3/TYPE4/TYPE5 are not output with IP transmission modes
(H.264/H.265/M-JPEG).
• TYPE4/TYPE5 are not output with SMPTE ST2110 and High
bandwidth NDI.
TONE [OFF, ON]
Make the settings for the test tone signal (1 kHz) output while the
color bar is displayed.
OFF Test tone is not output.
ON Test tone is output.
TALLY
TALLY [ENABLE, DISABLE]
Set whether to disable [DISABLE]/enable [ENABLE] the function that
makes the tally lamps turn on or turn off with the tally control signal.
TALLY BRIGHTNESS [LOW, MID, HIGH]
Adjust the brightness of the tally LEDs.
TALLY GUARD [OFF, ON]
The following functions are suppressed only during input of the R tally
signal:
- Auto white balance and auto black balance operation
- OSD menu display
- OSD status indicators
TALLY LED LIMIT
Set whether to limit the lighting of the tally lamps for each of the tally
control signal colors (R/G/Y).
R [LIMIT, UNLIMIT]
G [LIMIT, UNLIMIT]
Y [LIMIT, UNLIMIT]
LIMIT Limit the lighting of the tally lamps.
UNLIMIT Light the tally lamps.
<NOTE>
• If [LIMIT] is selected for [TALLY LED LIMIT], only the tally lamps
of this unit are limited. The tally status display on external devices
(the AW-RP150, AW-RP60 controller, etc.) remains enabled.
EXTERNAL OUTPUT
Select the type of signal to be output from the External Output signal
lines (Output1 and Output2) of the RS-422 connector. (→ page 20)
OUTPUT1
[OFF, R‑TALLY, G‑TALLY, Y‑TALLY]
OUTPUT2
[OFF, R‑TALLY, G‑TALLY, Y‑TALLY]
OFF Signal is not output.
R-TALLY The reception status of the red tally signal is output.
G-TALLY The reception status of the green tally signal is output.
Y-TALLY The reception status of the yellow tally signal is output.
TSL5.0
Make settings related to TSL protocol version 5.0.
With the TSL5.0 function, set the information required to control the
tallies of this unit from a device that supports the TSL5.0 protocol.
INDEX NO. [1 to 65534]
By matching the INDEX set on the TSL5.0 control device and the
Index number of this unit, you can control the tallies of this unit
individually.
PORT [1 to 65535]
Set the port number that will receive controls via the TSL5.0
protocol.
49
Camera menu items (continued)
To Next Page
Loading...
