Panasonic SA-PM4E - IC7002 (BA5948 FPE2) IC 4 CH Drive; Ic800 (Mn101 Ef16 Zxw) Microprocessor

Pin No. Mark I/O Function
1 IN2 I Motor Driver Input
2 PC2 I Turntable Motor Drive Signal
(“L”:ON)
3 IN1 I Motor Drive (1) Input
4 PC1 - Traverse Motor Drive Signal
(“L”): ON)
5-8 N.C. - No Connection
9 PGND1 - Ground Connection (1) for Drive
10 PVCC1 - Power Supply (1) for Drive
11 D1- O Motor Drive (1) reverse - action
output
12 D1+ O Motor Drive (1) forward - action
output
13 D2- O Motor Drive (2) reverse - action
output
14 D2+ O Motor Drive (2) forward - action
output
Pin No. Mark I/O Function
1 PCONT1 O Power Control Output 1(Pwr
Sply,Active HIGH)
2 PCONT2 - No Connection
3 NC - No Connection
4 FL_DATA /
OCD_SDA
I FL Data Output / On Chip
Debugger Data
5 NC - No Connection
6 FL_CLK /
OCD_SCL
I FL CLK Output / On Chip
Debugger Clock
7 NC - No Connection
8 NC - No Connection
9 NC - No Connection
10 NC - No Connection
11 MMOD - Memory mode selection
12 OSC2 (8MHz) O Main Oscillator output (8MHz)
13 OSC1 (8MHz) I Main Oscillator input (8MHz)
14 VSS - Micom GND
15 XI (32KHz) I Slow Oscillator input (32KHz)
16 XO (32KHz) O Slow Oscillator output (32KHz)
17 3.3V - Voltage supply 3.3V
18 Internal Output
(1.8V)
- Connect to pin 37
19 NRST I/O MICOM RESET PIN (L: reset)
20 NC - No Connection
21 NC - No Connection
22 NC - No Connection
23 NC - No Connection
24 DAB_PCONT - DAB module power control
25 RMT I Remote Control Input
26 NC - No Use
27 DAB_DDOW
FIC
I DAB LSI 24ms synchronization
interrupt
28 DAB_IRQ I DAB LSI interrupt (currently
unused)
29 BLKCK I CD Subcode Block Clock Input
30 VCCDET I VCC Failure Detect Signal ("L"
when AC in)
31 CD_MDATA I/O CD LSI Command Data
32 STAT I CD LSI Status Input
33 CD_MCLK I CD LSI Command Clock
34 N.C. - No Connection
35 CD_MLD O CD LSI Command Load
36 N.C. - No Connection
37 1.8V - Power Supply (1.8V)
38 MUTEA O Analog MUTE Output(L:MUTE
ON)
Pin No. Mark I/O Function
15 D3- O Motor Drive (3) reverse - action
output
16 D3+ O Motor Drive (3) forward - action
output
17 D4- O Motor Drive (4) reverse - action
output
18 D4+ O Motor Drive (4) forward - action
output
19 PVCC2 - Power Supply (2) for Driver
20 PGND2 - Ground Connection (2) for Driver
21-24 N.C. - No Connection
25 VCC I Power Supply terminal
26 VREF I Reference Voltage Input
27 IN4 I Motor Driver (4) Input
28 IN3 I Motor Driver (3) Input
Pin No. Mark I/O Function
39 VSS - Micom GND
40 ASP_CLK O ASP Sound Processor Serial
Clock Output
41 ASP_DATA O ASP Sound Processor Serial
Data Output
42 NC - No Connection
43 NC - No Connection
44 NC - No Connection
45 CD_RST O CD LSI Reset Ouput (L: reset)
46 N.C. - No Connection
47 Demo_Set I Demo Mode Setting Input
48 MODEL_SEL - Model Select (H: PM4, L: PM45)
49 PLL_DO O Data out for Tuner (PLL Data
I/O)
50 PLL_DI I Data in for Tuner (PLL Data I/O)
51 PLL_CLK - Clock for Tuner (PLL Clock
Output)
52 VOL_JOG1 I Jog Input 1
53 VOL_JOG2 I Jog Input 2
54 PLL_CE O Tuner Tuned Signal
55 N.C. - No Connection
56 N.C. - No Connection
57 N.C. - No Connection
58 N.C. - No Connection
59 N.C. - No Connection
60 MBP1 I/O Microp-beatproof
61 MBP2 I/O Microp-beatproof
62 CRTIMER - CRTIMER
63 VSS - Micom GND
64 FL_STROBE - Chip select for FL Panel
65 N.C. - No Connection
66 N.C. - No Connection
67 N.C. - No Connection
68 N.C. - No Connection
69 N.C. - No Connection
70 N.C. - No Connection
71 N.C. - No Connection
72 N.C. - No Connection
73 RDS_DATA I RDS Data Input
74 RDS_CLK O RDS Clock Input
75 N.C. - No Connection
76 N.C. - No Connection
77 N.C. - No Connection
78 N.C. - No Connection
79 N.C. - No Connection
80 N.C. - No Connection
18.2. IC7002 (BA5948FPE2) IC 4CH Drive
18.3. IC800 (MN101EF16ZXW) MICROPROCESSOR
59
SA-PM4E / SA-PM4EB / SA-PM4EG