Pentair Biffi ICON 2000 - Page 35

35
BIFFI ICON 2000
InstructIon and operatIng manual
Motor
Start
position%
Stop
position%
On time On time On time
Off
time
Off
time
Off
time
Start position and stop position may be adjusted
from0%-100%separatelyinopeningand
closing direction.
ON time and OFF time may be adjusted from
1 sec - 200 sec separately in opening and
closing direction.
Configuration procedure
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP. Select
the language and then enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”press
YES. Press YES to select actuator set-up
menu, press NO to scroll the list of available
routines and then press YES to select
2-speed timer.
•PressYEStochangeclosedirection
parameters, press NO and then YES to
change only open direction parameters.
Closing direction
•PressYESifthestatusisOK,orNO
to change. Press YES to confirm
(status = On, enables 2-speed timer operation
in closing direction status = Off, disables
timer operation in closing direction).
•PressYESifthepositionvaluewherepulsing
control starts is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
•PressYESifthepositionvaluewherepulsing
control stops is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
•PressYESifthevalueoftheONtimeof
pulsing control is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
•PressYESifthevalueoftheOFFtimeof
pulsing control is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
Opening direction
•PressYESifthestatusisOK,orNOto
change. Press YES to confirm (status = On
enables 2-speed timer operation in opening
direction status = Off, disables timer
operation in opening direction).
•PressYESifthepositionvaluewherepulsing
control starts is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
9.1.11 2-Speed timer
The “2-speed timer” routine is used to extend
the actuator travelling time in opening and/or
closing direction, by driving the motor by
pulses which duration (ON and OFF time) is
configurable. Pulsing control can be applied to
full travel or only a part of it.
•PressYESifthepositionvaluewherepulsing
control stops is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
•PressYESifthevalueoftheONtimeof
pulsing control is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
•PressYESifthevalueoftheOFFtimeof
pulsing control is correct, press NO to scroll
the list of available values. Press YES when
the value is correct.
9.1.12 BUS (or FDI control)
This routine is only available if a fieldbus
interface card is present. The routine allows
setting the most important parameters
(node address, termination, etc.) necessary
to connect the actuator to a fieldbus. If the
ICON 2000 was set to work with fieldbus, but
the fieldbus card is not present, a Hardware
alarm will be generated. Different interfaces
are available to connect the ICON 2000 to
different types of fieldbus. If the bus interface
is LonWorks, the routine “BUS” changes in
“FDI control”. See the specific manuals for
instruction and setting of the above modules.
9.1.13 Miscellaneous
It includes different types of routines as “time
and date”, “factory settings”, “lithium battery”,
“torque profile”, etc. used only for special
application or in particular conditions.
9.1.13.1 Time and date
Time and date are used in maintenance
functions to associate the time information to
the memorized event (torque profile, alarm
log, maintenance request, etc.). Time and date
are entered at the time of manufacture, but
they can be adjusted during commissioning or
maintenance operations.
Configuration procedure
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP.
Select the language and enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”press
YES. Press YES to select actuator set-up
menu, press NO to scroll the list of available
routines and then press YES to select
Miscellaneous.
•PressYEStoenterthetimeanddateroutine.
•PressYESifthetimeiscorrect,pressNOto
change it.
•Enterhours,minutesandseconds.PressNO
to scroll the list of available values, press YES
to select.
•PressYESwhenthetimeiscorrect.
•PressYESifthedateiscorrect,pressNOto
change.
•Enterday,month,andyear.PressNOto
scroll the list of available values, press YES to
select.
•PressYESifthedateiscorrect.