Pentair Biffi ICON 2000 - Maintenance Routines

38
BIFFI ICON 2000
InstructIon and operatIng manual
9.3.3 Set torque reference
The set torque profile reference routine
allows to transfer the last torque profile to the
reference profile registers. The old reference
data are lost and the new ones are used as a
new reference torque profile.
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP.
Select the language and enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”pressYES.
Press NO to scroll the list of available menus
and then press YES to select maintenance
menu.
•PressNOtoscrollthelistofavailable
routines and then press YES to select Set
torque reference.
•PressYEStoupdatethetorquereference
data.
9.3.4 Set curve reference
The “set curve reference” routine allows to
select 1 off 100 opening and closing torque
curves in the memory of the ICON 2000 and to
transfer them to the torque curve reference
registers. The old reference data are lost and
the new ones will be the new torque curves
reference (see VIEW mode, Maintenance,
Torque curve, paragraph 10.4.3).
Configuration procedure
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP. Select
the language and then enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”pressYES.
Press NO to scroll the list of available menus
and then press YES to select maintenance
menu.
•PressNOtoscrollthelistofavailable
routines and then press YES to select Set
curve reference.
•PressNOtoscrollthelistandthenpressYES
to select the desired curves (in opening and
closing).
•PressYEStoupdatethetorquecurve
reference.
9.3.5 Clear recent data log
The clear recent data log routine allows to
clear the counters of the recent operation log.
This command does not affect the content of
the “general operation log”.
The date of the “clear recent data log”
is memorized and can be viewed in the
maintenance date routine of the view menu.
9.3 MAINTENANCE
A large amount of data is stored in the actuator
memory and is available for future analysis
or to assist the operator in the maintenance
program. The maintenance menu also includes
the set password routine and the possibility to
modify or start the maintenance functions.
The following data are available:
- set password
- clear alarm log
- set torque reference
- set curve reference
- clear recent data log
- set maintenance date
- set data logger
9.3.1 Set password
The actuator is supplied by Biffi with a default
password (“0 0 0 0”). By the above routine
the end user can enter a different password
consisting of 4 alphanumeric characters. After
entering the new password, the old one ceases
to be valid. Therefore it is mandatory “NOT TO
FORGET THE PASSWORD” after the default
one has been modified. Forgetting the new
password makes it impossible to enter the
set-up menu and to configure the actuator.
Configuration procedure
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP.
Select the language and enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”pressYES.
Press NO to scroll the list of available menus
and then press YES to select Maintenance
menu.
•PressNOtoscrollthelistofavailable
routines and then press YES to select Set
password.
Press YES again to select Enter new
password.
•Enterthenewpasswordonedigitatatime.
Press YES if the digit is correct, press NO
to scroll the list of available characters and
then press YES to select. Enter 4 digits. When
the display shows the message Password
changed the old password is no longer valid.
9.3.2 Clear alarm log
Clear procedure
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP.
Select the language and enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”pressYES.
Press NO to scroll the list of available menus
and then press YES to select the Maintenance
menu.
•PressNOtoscrollthelistofavailable
routines and then press YES to select clear
alarm log.
•PressYEStoclearalarmlog.
Clearing procedure
•MovethelocalselectortoOFFandthen
simultaneously press OPEN and STOP.
Select the language and enter the password
according to the instructions (see “Entering
the set-up mode”). When the message
displayedis“SET-UPMODEOK?”pressYES.
Press NO to scroll the list of available menus
and press YES to select the maintenance
menu.
•PressNOtoscrollthelistofavailable
routines and then press YES to select clear
recent data log.
•PressYES.
•PressYEStoclearorpressNOtoexit.