Pfaff 3307-1 SERIES - Missed Stitch Detection Key

108 pages

Save Page as PDF

To Next Page

To Previous Page

Controls

7 - 5

7.06 Missed stitch detection key

● Key 1 lights up, when an error is

detected in the sewing process.

● Acknowledge the error signal by pressing

key 1.

Fig. 7 - 05

Main Page

Instruction Manual1
Table of Contents3
Contents4
Safety6
Regulations6
General Notes on Safety6
Safety Symbols7
Important Notes for the User7
Notes for Operating and Technical Staff8
Operating Staff8
Technical Staff8
Danger Warnings9
Proper Use10
Specifications11
General Information11
Seam Pattern Sizes12
Disposal of Machine13
Transportation, Packing and Storage14
Transportation to Customer's Premises14
Transportation Inside the Customer's Premises14
Disposal of Packing Materials14
Storage14
Explanation of Symbols15
Controls16
Main Switch16
Pedal16
Balance Wheel17
Adjusting the Button Clamp (Only on Subclass -1/.)17
Control Panel18
Missed Stitch Detection Key20
Installation and Commissioning21
Installation21
Adjusting the Table Height21
Drilling Template for the Table-Top22
Connecting the Plug-In Connections and Earth Cable23
Fitting the Reel Stand24
Commissioning24
Switching the Machine on / off24
Setting the Seam Pattern Size25
Establishing the Value for Parameter "20425
Changing Parameter "20426
Setting up27
Inserting the Needle27
Threading the Sewing Threads on the Subclass -128
Threading the Needle Thread (Sub-Class -429
Selecting the Button Type and Program Number30
Adjusting the Button Clamp to the Button Size (Only for Sub-Class -130
Sewing31
Sewing with Sub-Class -131
Sewing with Sub-Class -433
Sewing with Sub-Class -534
Input35
Seam Pattern Input on Machines from Subclasses -135
Seam Pattern Input for Two-Hole and Self-Shank Buttons35
Seam Pattern Input for Three-Hole Buttons37
Seam Pattern Input for Four-Hole Buttons39
Seam Pattern Input on Sub-Class -442
Parameter Input44
Selecting and Changing Parameters44
Entering/Changing the Access Code45
Assigning Access Rights46
Care and Maintenance47
Cleaning the Machine47
Cleaning the Hook Compartment48
Cleaning the Air Filter/Lubricator48
Checking/Adjusting the Air Pressure49
Oil Level for the Needle Drive Unit49
Oil Level for the Gears50
Adjustment51
Notes on Adjustment51
Tools, Gauges and Other Accessories51
Abbreviations51
Toothed Belts of the Main Drive52
Top Needle Bar Position (Reference Position)53
Pre-Adjusting the Needle Height54
Position of the Needle to the Needle Hole55
Basic Position "Button Clamp Raised56
Sensor Board of the Needle Drive (in Dismantled Condition)57
Basic Setting of the Needle Drive59
Position of the Hook Shaft to the Needle60
Adjusting the Drag Link Mechanism61
Needle Rise and Hook Clearance62
Readjusting the Needle Height64
Adjusting the Loop Spreader65
Position of the Loop Spreader to the Needle66
Adjusting the Thread Trimmer67
Manual Cutting Test68
Adjusting the Thread Catcher69
Adjusting the Thread Loop Support70
Basic Position of the Button Clamp Drive71
Aligning the Button Clamp (Only on Subclass -172
Aligning the Work Clamp (Only on Subclass -473
Aligning the Button Holder and Button Support (Only on Sub-Class -574
Adjusting the Clamp Pressure (Only on Subclass -175
Aligning the Cloth Plate (Only on Subclass -176
Basic Setting of the End Knotting Equipment77
Adjusting the Retaining Finger of the End Knotting Equipment78
Adjusting the Lifting Lever of the End Knotting Equipment79
Adjusting the Reed Switch80
Setting the Angle for the End Knotting (Only on Subclasses -181
Adjusting the Moment Tension82
Adjusting the Thread Puller83
Adjusting the Thread Clamp84
Adjusting the Thread Regulator85
Adjusting the Button Holding Cylinder (Only on Subclass -586
Adjusting the Thread Wiper (Only on Subclass -587
Cold Start88
Parameter Settings89
Selecting and Altering Parameters89
Parameter List90
Error Messages on the Display95
Motor Errors97
Data Backup and Protection with PC-Program SAM98
Internet Update of the Machine Software99
Wearing Parts100
Circuit Diagrams102

Pfaff 3307-1 SERIES - Missed Stitch Detection Key

Table of Contents

Related product manuals