Pioneer PDP-4270XA User Manual

Setting up 08
33
En
English
Note
• You cannot adjust the front surround effect for listening with
headphones.
• If you change the front surround effect with headphones
connected, the new setting will become effective as soon as you
disconnect the headphones.
• (WOW) designates a status where the FOCUS is on and
TruBass + SRS has been selected for Front Surround.
• is a trademark of SRS Labs, Inc.
• WOW technology is incorporated under license from SRS Labs,
Inc.
• The effect of this function differs depending on signals.
Power Control
Power Control provides convenient functions for power saving.
Energy Save
You may use one of the three Energy Save modes to save power
consumption.
1 Press HOME MENU.
2 Select “Power Control“ (/ then ENTER).
3 Select “Energy Save“ (/ then ENTER).
4 Select “Save1“, “Save 2“, or “Picture Off“ (/ then ENTER).
5 Press HOME MENU to exit the menu.
Note
• When you change the Energy Save mode, you may notice a change
in the panel sound. This is normal.
No Signal off
The system will be automatically placed into the standby mode if no
signal is received for 15 minutes.
1 Press HOME MENU.
2 Select “Power Control“ (/ then ENTER).
3 Select “No Signal off“ (/ then ENTER).
4 Select “Enable“ (/ then ENTER).
5 Press HOME MENU to exit the menu.
Note
• Five minutes before the system is placed into the standby mode, a
message appears every minute.
• The system may not be placed into the standby mode when noise
signals are present at the plasma television after a TV programme
finishes.
No Operation off
The system will be automatically placed into the standby mode when
no operation is performed for three hours.
1 Press HOME MENU.
2 Select “Power Control“ (/ then ENTER).
3 Select “No Operation off“ (/ then ENTER).
4 Select “Enable“ (/ then ENTER).
5 Press HOME MENU to exit the menu.
Note
• Five minutes before the system is placed into the standby mode, a
message appears every minute.
Energy Save
Selections Standard Does not decrease the picture brightness.
Save1 Slightly lowers power consumption while
slightly suppressing the brightness drop level.
Save2 Decreases the picture brightness and lowers
power consumption.
Picture Off Deactivates the screen to save power. To
restore the screen display, press any button
other than i +/i – and e.
This setting is not memorized by the system.
No Signal Off
Selections Disable (default) Does not place the system into the standby
mode.
Enable Places the system into the standby mode if no
signal is received for 15 minutes.
No Operation Off
Selections Disable (default) Does not place the system into the standby
mode.
Enable Places the system into the standby mode if no
operation is performed for three hours.

Pioneer PDP-4270XA Specifications

General

3D	No
Depth	115 mm
Width	1040 mm
Height	679 mm
Weight	31500 g
Tuner type	Analog
Pixel pitch	- mm
Product color	Black, Silver
Noise reduction	Yes
RMS rated power	26 W
AC input voltage	220 - 240 V
Display diagonal	42 \
Channels quantity	99 channels
AC input frequency	50 - 60 Hz
Display brightness	1100 cd/m²
Display resolution	1024 x 768 pixels
Display technology	Plasma
Number of speakers	2
Teletext standards	Top-text
SCART ports quantity	3
USB 2.0 ports quantity	0
Annual energy consumption	- kWh
Display diagonal (metric)	106 cm
Analog signal format system	NTSC, NTSC 3.58, NTSC 4.43, PAL, PAL 60, PAL BG, PAL DK, PAL I, SECAM, SECAM B/G, SECAM D/K, SECAM L
Power consumption (standby)	0.3 W
Power consumption (typical)	287 W
Digital signal format system	-
Sound enhancement technology	FOCUS, SRS, TruBass
On Screen Display (OSD) languages	CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, GRE, ITA, NOR, POL, POR, RUS, SWE