Protec 6100 - Table of Contents

N93-572-88 Issue 12 NH Page 3 of 52 © Protec Fire Detection plc 2020
Table of Contents
IMPORTANT NOTES – PLEASE READ CAREFULLY ................................................................................... 5
STANDARDS, DIRECTIVES AND REGULATIONS INFORMATION ............................................................. 6
1.0 ITEMS SUPPLIED WITH THE 6100 ...................................................................................................... 7
2.0 ITEMS AND INFORMATION REQUIRED PRIOR TO COMMISSIONING ............................................ 7
2.1 Site information required to commission the 6100 .......................................................................... 7
2.2 Items required to commission the 6100 using the windows software .............................................. 7
3.0 INTRODUCTION AND KEY FEATURES ............................................................................................... 8
4.0 6100 CABLING REQUIREMENTS ........................................................................................................ 9
4.1 General ............................................................................................................................................ 9
4.2 Mains Input Rating Label ................................................................................................................. 9
4.3 Mains Wiring .................................................................................................................................... 9
4.4 Alarm Circuit Wiring ......................................................................................................................... 9
4.5 Fire Link Wiring .............................................................................................................................. 10
4.6 Addressable Loop Wiring and Devices .......................................................................................... 10
5.0 INSULATION TESTING OF CABLING PRIOR TO CONNECTION .................................................... 12
6.0 INSTALLING THE 6100 ....................................................................................................................... 13
6.1 Unpacking ...................................................................................................................................... 13
6.2 Removal of the Door ...................................................................................................................... 13
6.3 Disconnection of the Fire Brigade Panel (FBP) Connections ........................................................ 14
6.4 Removal of the Control PCB Housing ........................................................................................... 15
6.5 Preparing the Mounting Position and Cable Entries ...................................................................... 16
6.6 Installing the Standby Batteries ..................................................................................................... 16
6.7 Connecting the Standby Batteries ................................................................................................. 17
6.8 Refitting the Control PCB Housing ................................................................................................ 18
6.9 Connecting the Addressable Loop Wiring ..................................................................................... 18
6.10 Connecting the Conventional Alarm Circuit Wiring .................................................................... 18
6.11 Connecting the Fire Link Wiring ................................................................................................. 19
6.12 Connecting the Auxiliary Wiring ................................................................................................. 19
6.13 Connecting the Mains Cabling ................................................................................................... 20
6.14 Connecting the Fire Brigade Panel Controller ........................................................................... 21
6.15 Re-fitting the Door ...................................................................................................................... 21
6.16 Switching the Mains Power On .................................................................................................. 21
7.0 COMMISSIONING THE 6100 ............................................................................................................... 22
7.1 Terminology ................................................................................................................................... 22
7.2 Loop Device Input Group, Output Group and Zone Programming ................................................ 22
7.3 Non latching Loop Devices ............................................................................................................ 22
7.4 Loop Device Class Programming .................................................................................................. 23
7.5 Loop Device Sensitivity Programming ........................................................................................... 24
7.6 Loop Sounder Volume Programming ............................................................................................ 24
7.7 Talking Sounder Programming Considerations ............................................................................. 25
7.8 Fire Link Operation ........................................................................................................................ 26
7.9 Global Fire Contact Operation ....................................................................................................... 27
7.10 Global Fault Contact Operation ................................................................................................. 27
7.11 Remote Alarm Input Operation .................................................................................................. 27
7.12 Class Change Input Operation ................................................................................................... 27
7.13 Conventional Alarm Output Operation ....................................................................................... 28
7.14 Output Group Type .................................................................................................................... 28
7.15 Output Group Delays (T1 and T2) ............................................................................................. 28
7.16 Programming the coverage volume of Visual Alarm Devices (VADs) ....................................... 30
7.17 Logging and Mapping Loop Devices .......................................................................................... 30
7.18 Programming Loop Device Address Data .................................................................................. 32
7.19 Exchanging Loop Devices ......................................................................................................... 34
7.20 Disabling / Enabling a Loop Device ........................................................................................... 35
7.21 Loop Device Remote Visual Address Verification ( RVAV ) ...................................................... 36