Reliance 7900 - ADVANCED ROOM LIGHT PROGRAMMING; Programming Navigation and Zone Setup; Scene Levels and Pico Wireless Control

IN-7900
21
3.8.3.7. Master Buttons
The Master buttons allow you to move through the menu
choices. The current choice is highlighted on the info screen.
3.8.3.8. OK Button
The OK button chooses the current highlighted menu
choice. This will either take you to the next menu or
accept a setting you have selected. When the screen
displays a Yes/No question, the OK button is “Yes”.
3.8.3.9. Timeclock Button
The Timeclock button functions as a “back” button during
programming mode. Pressing the Timeclock button
takes you back one step in the current menu. Pressing
it repeatedly will eventually return you to the main menu,
but will not exit programming mode. When the screen
displays a Yes/No question, the Timeclock button is “No”..
3.8.3.10. Zone Setup
3.8.3.11. Assigning Load Types
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone setup” and
press the OK button to accept.
3. Use the Master buttons to highlight “Load type”. Press
the OK button to accept. See “Setting Load Types” table
on the next page.
4. Use the zone raise/lower buttons to choose the load
type for that zone. See the list on the next page for
supported load types. Press the OK button to accept.
5. The info screen will conrm that your load type has
been saved.
6. Exit programming mode.
3.8.3.12. Assigning Non-Dim Load Types
Zones assigned to non-dim loads have three available
congurations:
• LOFO: Last On, First Off
• FOFO: First On, First Off
• FOLO: First On, Last Off
• LOLO: Last On, Last Off
• 60/40: On at 60%, off at 40%
In scenes including dim and non-dim load types, if set up
as “First” On/Off, non-dim loads will toggle before dim
loads; if set up as “Last” On/Off, dim loads will toggle
before non-dim loads.
1. Enter programming mode.
2. Use the Master buttons to highlight “Zone setup” and
press the OK button to accept.
3. Use the Master buttons to highlight “Non-Dim Load
type”. Press the OK button to accept. See “Setting Load
Types” table on the next page.
4. Use the zone raise/lower buttons to choose the non
dim load type for that zone. (Zones not programmed as
non-dim will be displayed as Unaffected.) Press the OK
button to accept.
5. The info screen will conrm that your load type has
been saved.
6. Exit programming mode.
3.8.3.13. Scene Setup
3.8.3.14. Setting Zone Levels, Fade Rates, and
Shade Group Actions
1. Enter programming mode.
2. Use the Master buttons to highlight “Scene setup” and
press the OK button to accept.
3. Use the Master buttons to highlight “Levels” to adjust
lighting and/ or shade levels. Press the OK button to
accept. Use the Master buttons to highlight the scene
number of your desired scene. Press the OK button to
accept.
4. Set each zone to the desired light level for this scene
using the zone raise/lower buttons. The info screen will
display the zone and percentage as you adjust it.
To set a zone as unaffected, lower the light levels all
the way to off, then hold the zone lower button for 3
seconds. The screen will display “---” and the three middle
LEDs for the zone will be lit to indicate this zone is
unaffected by the scene (the zone will not change when
this scene is initiated).
When all zones are at the desired level, press the OK
button to accept.
5. Use the Master buttons to set the fade time for this
scene. Press the OK button to accept.
6. Note: This step is applicable only if you have shades
on your system. If you do not have or do not wish to set
shade groups for this scene, press the OK button to skip
this step.
Set each shade group to the desired level for this scene.
When all shade groups are at the desired level, press the
OK button to accept.
For shade programming, see the full installation and
operation guide at www.lutron.com/qs.
7. The info screen will conrm that your scene has been
saved.
8. Exit programming mode.
3.8.3.15. Pico Wireless Control Setup
1. Make sure the wireless mode of the GRAFIK Eye QS
control unit is “Enabled”.
2. On the Pico wireless control, press and hold the top
(on) and bottom (off) buttons for 3 seconds. The info
screen on the GRAFIK Eye QS control unit will display
the Pico wireless control options. Press the OK button
on the GRAFIK Eye QS control unit to select the desired
operation type for the Pico wireless control.
3. Assign the Pico wireless control
a. To assign the Pico wireless control as a zone
controller, use the Master buttons to select “Zone” and
press the OK button to accept. Use the zone raise/