Response Alarms SA3 User Manual

Installation & Operating Manual
SA3
6 Zone Wirefree
Alarm System













       
     


Response Alarms SA3 Specifications

Power

sealed lead acid battery	6V/1.2Ahr
solar panel charge rate	60mA
battery life	> 1 year

RF and Range

rf operating frequency	433MHz
control panel range	75 metre max.
remote control range	50 metre max.

Weight and Dimensions

control panel width	185 mm
control panel depth	52 mm
control panel height	125 mm
magnetic contact detector width	52 mm
magnetic contact detector height	125 mm
magnetic contact detector depth	12 mm
keypad width	110 mm
keypad height	30 mm

Summary

Foreword and Safety Information

System Security Overview

Discusses system design for intruder detection and deterrence, emphasizing the importance of physical protection.

General Safety Precautions

Provides essential safety advice for using tools, ladders, and working near the siren.

Declaration of Conformity

States compliance with the Radio and Telecommunications Terminal Equipment (R&TTE) directive.

Kit Contents

Introduction and System Overview

System Arming Modes

Explains the Full Arm and Part-Arm modes of operation for the alarm system.

Entry and Exit Delay Configuration

Details how entry and exit delays are programmed and function within the system.

Alarm Zones and Operating Modes

Describes the system's 6 wirefree alarm zones and their configurable operating modes.

Zone Lockout Feature

Explains the feature that temporarily disables zones after multiple false alarms.

Tamper Protection

Covers tamper features on devices to protect against unauthorized interference.

Jamming Detection

Describes the system's feature to detect and alarm on radio jamming attempts.

Battery Monitoring System

Explains how the system monitors battery levels and provides low battery warnings.

System House Code Configuration

Details setting a unique House Code for system security and device communication.

Planning and Extending Your Alarm System

Typical Installation Layout

Provides a visual guide and explanation of typical device placement in a property.

Remote Control Unit Operation

Control Panel Placement

Installing the Control Panel

Configuring Control Panel House Code

Details the process of setting the system's unique House Code via the control panel.

Testing Control Panel and Remote

Instructions to test the interaction between the control panel and remote control.

Passive Infra-Red (PIR) Movement Detectors

PIR Detector Positioning

Provides recommendations for optimal PIR detector placement for effective coverage.

PIR Detector Installation and Configuration

Guides through the physical installation and setup of PIR detectors.

Testing the PIR Detector

Instructions for testing the PIR detector's functionality and sensitivity.

Magnetic Contact Detectors

Magnetic Contact Detector Positioning

Provides recommendations for optimal placement of magnetic contact detectors.

Magnetic Contact Detector Installation and Configuration

Guides through the physical installation and setup of magnetic contact detectors.

External Solar Siren

Solar Siren Positioning

Provides recommendations for optimal siren placement for visibility and audibility.

Solar Siren Installation and Configuration

Guides through the physical installation and setup of the solar siren.

Powering Up and Testing the Siren

Instructions for connecting batteries and testing the siren's operation.

External Connections

System Testing Procedures

Detector Testing

General instructions for testing all types of detectors within the system.

Remote Control Tests

Specific test procedures for the remote control unit.

Detector Function Tests

Tests for PIR and Magnetic Contact detectors to verify operation.

System Component Tests

Tests for relays, siren, and control panel LEDs to verify system functionality.

Siren Service Mode

Explains how to put the siren into service mode for maintenance.

Factory Settings Management

Factory Settings Overview

Lists the default factory settings for the alarm system.

Resetting to Factory Defaults

Step-by-step guide to reset the system to its original factory settings.

Programming Instructions

User Access Code Programming

Instructions on how to change the system's user access code.

System House Code Configuration

How to configure the system's unique house code for device communication.

Instant and Delay Zones

Defines zones that trigger instantly or with an entry/exit delay.

Entry/Exit Delay Settings

Configuration for the entry and exit delay periods.

Alarm Duration Settings

Setting the length of time the alarm will sound.

Part-Arm Configuration

Controls which zones are active when the Part-Arm feature is enabled.

Zone Lockout Configuration

Configures the zone lockout feature which limits zone alarms after multiple triggers.

Entry/Exit Warning Tone

Controls whether entry/exit delay beeps are enabled or disabled.

Jamming Detection Configuration

Enables or disables the Control Panel's anti-jamming detection feature.

Signalling Relay Contacts

Controls the operation period of the switching relay contacts following an alarm.

Zone Operating Modes

Defines modes for alarm zones (PA, Intruder, Fire, Test).

Operating Instructions

Arming and Disarming Modes

Covers procedures for setting the system to Full Arm, Part-Arm, and Disarming.

Special Alarms and Modes

Covers Personal Attack alarms, Device Tamper, and Siren Service Mode.

Siren Operating Mode

Instructions on how to switch the siren back to operating mode after service.

Battery Monitoring Indicators

Details how low battery status is indicated for different system devices.

Maintenance Procedures

Solar Siren Maintenance

Maintenance advice specific to cleaning the solar panel and battery care.

Control Panel and Battery Maintenance

Maintenance for the control panel, detectors, remote control, and batteries.

Product Disposal Guidelines

Guidance on the proper disposal of the product and its batteries.

Alarm Record Log

Troubleshooting Common Issues

Control Unit Power and Battery Issues

Troubleshooting power failures and low battery warnings on the control unit.

Access Code and System Communication Problems

Solutions for incorrect access codes and communication failures between components.

Alarm Activation and Sounding Issues

Diagnosing problems with alarms triggering or not sounding correctly.

Detector Specific Issues

Troubleshooting problems specific to the remote control and PIR detectors.

PIR Detector Operation and False Alarms

Diagnosing PIR detector movement detection and false alarm issues.

Magnetic Contact Detector Operation and False Alarms

Troubleshooting magnetic contact detector functionality and false alarms.

Extending Your Alarm System

Available Accessories

Details various accessory kits and components to enhance the system.

Product Guarantee Information

Outlines the product guarantee terms, conditions, and claim procedures.

Component Specifications

Siren and Control Panel Specifications

Technical details for the external solar siren and control panel.

Detector and Remote Specifications

Technical details for detectors, remote controls, and keypad.

Support Information

Includes Helpline contact details and R&D policy.