To Next PageTo Next Page
Why are documents not printing from my Ricoh All in One Printer?
If documents and reports do not print out from your Ricoh All in One Printer, it might be because the paper output tray is full. Remove the prints from the tray. Another reason could be that there is no paper left. Load paper into the printer.
Why does my Ricoh All in One Printer have frequent misfeeds?
If misfeeds occur frequently with your Ricoh All in One Printer, it could be due to using curled paper. Try to straighten out the curl. Load the paper upside down so that the curled edges face downward. Another reason could be that the tray's side or end fences may not be set properly. Remove misfed paper and check that the side or end fences are set properly.
What to do if error message remains after removing paper from Ricoh All in One Printer?
If an error message remains on your Ricoh All in One Printer, even after removing misfed paper, it could be because you need to open and close the cover as required. Also, paper might still be jammed in the tray. After removing misfed paper, fully open the front cover, and then close it.
Why can't I print in duplex mode with my Ricoh All in One Printer?
If you cannot print in duplex mode on your Ricoh All in One Printer, you may have selected a paper tray that is not set for duplex printing. Change the setting for "Apply Duplex" in [Tray Paper Settings] to enable duplex printing for the paper tray. Another reason could be that you have selected a paper type that cannot be used for duplex printing. In [Tray Paper Settings], select a paper type that can be used for duplex printing.
What to do if an error has occurred on my Ricoh All in One Printer?
If an error has occurred on your Ricoh All in One Printer, it may be because a function which has the status "Error Occurred" in the [Check Status] screen is defective. Press [Check] in the function which the error has occurred. Then check the displayed message, and take appropriate action. You can use other functions normally.
What to do if error message remains after closing the cover on Ricoh All in One Printer?
If an error message remains displayed even if the indicated cover is closed on your Ricoh All in One Printer, one or more covers that are not indicated are still open. Close all the covers of the machine.
How to turn on the display on Ricoh All in One Printer?
If your Ricoh All in One Printer display is off, the machine might be in Low Power mode. To cancel it, touch the display panel or press one of the keys on the control panel. Alternatively, the machine may be in Sleep mode. Press the [Energy Saver] key or the [Check Status] key to cancel Sleep mode.
Why is my Ricoh All in One Printer unable to connect to the network?
If the machine is unable to connect to the network, it could be due to a network error. Check that the Ricoh All in One Printer is correctly connected to the network, and that the machine is correctly set.
Why are images printed on the reverse side of the paper by my Ricoh All in One Printer?
If original images are printed on the reverse side of the paper by your Ricoh All in One Printer, you may have loaded the paper incorrectly. Load paper into the paper tray with the print side down. Load paper into the Large Capacity Tray (LCT), or the bypass tray with the print side up.
Why won't my Ricoh All in One Printer enter sleep mode?
If the indicator lamp remains lit and the Ricoh All in One Printer does not enter Sleep mode even though the [Energy Saver] key was pressed, this could be because the ADF is open, the machine is communicating with external equipment, the hard disk is active or the machine is cooling down. Close the ADF and check if the machine is communicating with external equipment. You can also wait a little longer.
Details security features to protect documents and prevent unauthorized access or copying.
Identifies and describes the various parts and components of the machine for user familiarity.
Provides instructions on the correct procedure for powering the machine on and off.
Outlines the fundamental steps required to make copies of documents using the machine.
Explains how the machine automatically adjusts copy size to fit selected paper, including rotation.
Details how to copy documents onto both sides of paper for paper saving.
Guides users through the simple process of installing printer drivers from the provided CD-ROM.
Provides solutions for common issues encountered when operating the machine.
General
