Home
RKI Instruments
Measuring Instruments
GX-2003
Page 144
RKI Instruments GX-2003 - Page 144
153 pages
Manual
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
50 • Viewing, Printing, Exporting, and Deleting Data
6.
T
ype the ne
w pass
word again, then click the Con
fi
rm New
P
assw
ord button.
7.
Clic
k
OK
when the progr
am con
fi
r
ms that you ha
ve changed
the pass
word.
8.
Close the P
assw
ord window
.
143
145
Table of Contents
Main Page
Table of Contents
5
Chapter 1: Introduction
9
Overview
9
About the GX-2003
9
Specifications
11
About this Manual
12
Chapter 2: Description
13
Overview
13
Instrument Description
13
Case
14
Sensors
15
Lcd
16
Control Buttons
16
Printed Circuit Boards
16
Alarm LED Arrays
17
Infrared Communications Port
17
Buzzers
17
Vibrator
17
Batteries
17
Pump
18
Flow Chamber
18
Inlet Filter Holder
19
Standard Accessories
20
Tapered Rubber Nozzle
20
Protective Rubber Boot
20
Sample Hose & 10 Inch Probe
21
Bar Hole Probe
21
Chapter 3: Using the GX-203 in Normal Mode
22
Overview
22
Start Up, Normal Mode
22
Turning on the GX-2003, Normal Mode Only
22
Turning on the GX-2003 in Normal with All Modes Active
25
Performing a Demand Zero, Normal Mode
26
Turning off the GX-2003, Normal Mode
27
Measuring Mode, Normal Operation
27
Monitoring an Area
27
Combustible Gas Detection
28
Measuring Mode, Alarms
29
Alarm Indications
30
Resetting and Silencing Alarms
31
Responding to Alarms
32
Display Mode
33
HC Range Screen
34
ID Screen
35
Peak Screen
36
Elapsed Time Screen
36
TWA/STEL Screen
36
Date/Time/Battery Charge Screen
37
Clear Data Logger Screens
37
Remaining Log Time Screen
38
Datalogging
39
Data Cal 2000
39
Calibration Mode
40
Calibration Supplies and Equipment
40
Preparing for Calibration
41
Calibrating the GX-2003
41
Adjusting the LCD Contrast
46
Chapter 4: Using the GX-2003 in Bar Hole Mode
47
Overview
47
Start Up, Bar Hole Mode
47
Turning on the GX-2003, Bar Hole Mode
47
Performing a Demand Zero, Bar Hole Mode
50
Bar Hole Testing
51
Performing a Bar Hole Test
51
Turning off the GX-2003, Bar Hole Mode
53
Chapter 5: Using the GX-2003 in Leak Check Mode
54
Overview
54
Start Up, Leak Check Mode
54
Turning on the GX-2003, Leak Check Mode
54
Performing a Demand Zero, Leak Check Mode
57
Leak Testing
58
Locating a Leak
58
Turning the Buzzer on and off in Leak Check Mode
58
Turning off the GX-2003, Leak Check Mode
58
Chapter 6: Setup Mode
60
Overview
60
Tips for Using Setup Mode
61
Using Setup Mode
61
Updating the Alarm Point Settings
62
Updating the Lunch Break Setting
63
Updating the Alarm Latching Setting
64
Updating the Alarm Silence Setting
64
Updating the Confirmation Beep Setting
65
Updating the Interval Time Setting
65
Updating the Log Data over Write Setting
65
Updating the Date and Time Settings
66
Updating the Calibration Interval
66
Updating the Calibration Time Remaining Setting
67
Updating the Calibration Expired Action Setting
67
Updating the LCD Contrast Setting
68
Updating the GX-2003'S Serial Number
68
Turning the User ID Function on or off
69
Calibrating Using Auto Calibration
69
Calibrating Using Single Calibration
71
Updating the LCD Backlight Time Setting
73
Turning the Password Function on or off
73
Turning LB Mode Display on or off
74
Setting the Bar Hole Measurement Time
74
Exiting Setup Mode
75
Chapter 7: Maintenance
76
Overview
76
Troubleshooting
76
Replacing or Recharging the Batteries
78
Replacing Alkaline Batteries or Ni-MH Battery Pack
78
Recharging the Battery Pack in the Instrument
79
Recharging the Battery Pack out of the Instrument
80
Replacing the HC and CO Filters
81
Replacing a Sensor
82
Replacing the Hydrophobic Disk Filter, Cotton Filter
84
And Wire Mesh Disk
84
Parts List
86
Appendix A: Calibrating with a Sample Bag
88
Overview
88
Calibration Supplies & Equipment
88
Preparing for Calibration
89
Calibrating the GX-2003
90
Calibrating with the Auto Calibration Method
91
Calibrating with the Single Calibration Method
93
Parts List
94
Table of Contents
97
Introduction
99
System Requirements
100
Installing the GX-2003 Data Logging Software
101
Irda Downloading Cable
104
Installing an Irda Adapter Cable
104
Windows Wireless Link Operation Note
104
Using a USB or Serial Port with an Irda Cable Installed
106
Launching the Software
107
Control Buttons
108
Download Button
109
Instrument Information Button
109
Data Button
110
Last Calibration Button
111
Set Button
116
Downloading Data from the GX-2003
117
Viewing, Printing, Exporting, and Deleting Data
122
Data Window
122
Calibration History
123
Interval Trend Data
126
Alarm Trend Data
133
Event Data
139
Deleting Data
142
Changing the Password
143
Calibrating a GX-2003 with the Data Logging Software
145
Changing Data Logging Parameters
149
Changing the Appearance of the Software Screens
151
Spare Parts List
153
Other manuals for RKI Instruments GX-2003
Quick Reference Guide
2 pages
Related product manuals
RKI Instruments GX-2012
185 pages
RKI Instruments GX-3R
122 pages
RKI Instruments GX-8000
58 pages
RKI Instruments GX-6000
262 pages
RKI Instruments EAGLE 2
310 pages
RKI Instruments HS-04
100 pages
RKI Instruments beacon 410
66 pages
To Next Page
