Commissioning and Maintenance
© robatherm 49
Pos: 64.1 /Überschri ften/__Brennkam mer @ 0\mod_1257341714560_2 008.doc @ 2051 @ 2
Combustion Chamber
Pos: 64.2 /Inbetri ebnahme und Wartung/_Inbe triebnahme @ 0\mod_12579 29574289_2008.doc @ 2116 @ 3
Commissioning
Pos: 64.3 /Sicher heitshinweise/!Vor sicht_Sicherheitshi nweise beachten_Quer verweis @ 0\mod_125777 7093652_2008.doc @ 2112 @
Caution
Observe general safety instructions on page 3!
Pos: 64.4 /Sicherheitshinweise/IBN&Wartung/!IBN&Wartung_Vorsicht_heiße F lächen @ 0\mod_1258373421 988_2008.doc @ 2158 @
Caution
To avoid burns, do not touch hot surfaces.
Pos: 64.5 /Sicherheitshinweise/IBN&Wartung/!IBN&Wartung_Brennkammer_IB N_Vorsicht @ 0\mod_125844 4793747_2008.doc @ 2197 @
Caution
Observe requirements in line with DIN 4794, DIN 4755 and DVGW-worksheet (German
Technical and Scientific Association for Gas and Water) G600.
There is a danger of fire if flammable materials come into contact with the combustion
chamber.
Pos: 64.6 /Sicherheitshinweise/IBN&Wartung/!IBN&Wartung_Brennkammer/Gasf lächenbrenner_IB N_ATEX @ 0\mod_1258444798 263_2008.doc @ 2198 @
Operation in explosion hazard zones not permitted. Flush to ensure that no explosive
atmosphere is present before the burner ignites.
Pos: 64.7 /Sicherheitshinweise/IBN&Wartung/!IBN&Wartung_Brennkammer_IB N_Achtung @ 0\mod_1258444898 137_2008.doc @ 2199 @
Attention
First commissioning of a combustion chamber or the associated system must be carried
out by the manufacturer or a specialist appointed by the manufacturer following DIN 4794.
Pos: 64.8 /Inbetri ebnahme und Wartung/Brennka mmer/Brennkammer _Flammtopf @ 0\mod_125844 5003949_2008.doc @ 2200 @ 44
Flame Pot
Check position of flame pot; it must be positioned vertically by the back wall.
Connection
Installation of oil or gas burner in accordance with manufacturer's instructions. Connect
burner to oil or gas line. The operating instructions of the oil or gas burner manufacturer
must be followed exactly.
Install and wire all sensors and thermostats.
Pos: 64.9 /Sicherheitshinweise/IBN&Wartung/!IBN&Wartung_Brennkammer_IB N_Achtung2 @ 0\mod_125844509 6156_2008.doc @ 2201 @
Attention
Every system must be equipped with an emergency switch.
Overheating damage of combustion chamber, casing, components etc. may occur when
the unit is operated with insufficient cooling (e.g. the unit is switched off via crash switch
and burner is still running) or the units are switched off via safety bodies.
There is a danger of fire if flammable materials come into contact with the combustion
chamber.
Check that there is a good distribution of the airflow at the inlet and outlet of the
combustion chamber!
Pos: 64.10 /Inbetri ebnahme und Wartung/Brennk ammer/Brennkam mer_Verbrennungsluf t @ 0\mod_1258445162394_2 008.doc @ 2202 @ 4444
Combustion Air
The required combustion air (environmentally compatible) amounts to approx 1 m³/h per kW
installed burner capacity. The intakes should be designed inside the building following TRGI,
in the unit to a max. of 1 m/s, min. 150 cm².
To Next Page
Loading...