Rohde & Schwarz FSEA20 - Page 325

Command Assignment - Signal Analysis FSE
1065.6016.12 6.268 E-16
INSERT
VALUE
no corresponding IEC/IEEE-bus command
DELETE
VALUE
no corresponding IEC/IEEE-bus command
SHIFT X
LIMIT LINE
:CALCulate<1|2>:LIMit<1...8>:CONTrol:SHIFt <num_value>
SHIFT Y
LIMIT LINE
:CALCulate<1|2>:LIMit<1...8>:UPPer:SHIFt <num_value>
:CALCulate<1|2>:LIMit<1...8>:LOWer:SHIFt <num_value>
SAVE
LIMIT LINE
automatically executed during IEC/IEEE-bus operationh
EDIT LIMIT
LINE
:CALCulate<1|2>:LIMit<1...8>:UNIT DB| DBM| PCT |DBUV| DBMW | DBUA |
DBPW| DBPT | WATT| VOLT | AMPere | DBUV_MHZ | DBMV_MHZ| DBUA_MHZ |
DBUV_M | DBUV_MMHZ | DBUA_M | DBUA_MMHZ
:CALCulate<1|2>:LIMit<1...8>:COMMent ’string’
:CALCulate<1|2>:LIMit<1...8>:TRACe <num_value>
:CALCulate<1|2>:LIMit<1...8>:CONTrol[:DATA] <num_value>, <num_value>..
:CALCulate<1|2>:LIMit<1...8>:CONTrol:DOMain FREQuency|TIME
:CALCulate<1|2>:LIMit<1...8>:CONTrol:OFFset <num_value>
:CALCulate<1|2>:LIMit<1...8>:CONTrol:MODE RELative | ABSolute
:CALCulate<1|2>:LIMit<1...8>:CONTrol:SPACing LINear | LOGarithmic
:CALCulate<1|2>:LIMit<1...8>:UPPer[:DATA] <num_value>, <num_value>..
:CALCulate<1|2>:LIMit<1...8>:UPPer:STATe ON | OFF
:CALCulate<1|2>:LIMit<1...8>:UPPer:OFFset <num_value>
:CALCulate<1|2>:LIMit<1...8>:UPPer:MARGin <num_value>
:CALCulate<1|2>:LIMit<1...8>:UPPer:MODE RELative | ABSolute
:CALCulate<1|2>:LIMit<1...8>:UPPer:SPACing LINear | LOGarithmic
:CALCulate<1|2>:LIMit<1...8>:LOWer[:DATA] <num_value>,<num_value>..
:CALCulate<1|2>:LIMit<1...8>:LOWer:STATe ON | OFF
:CALCulate<1|2>:LIMit<1...8>:LOWer:OFFset <num_value>
:CALCulate<1|2>:LIMit<1...8>:LOWer:MARGin <num_value>
:CALCulate<1|2>:LIMit<1...8>:LOWer:MODE RELative | ABSolute
:CALCulate<1|2>:LIMit<1...8>:LOWer:SPACing LINear | LOGarithmic
:CALCulate<1|2>:LIMit<1...8>:FAIL?
:CALCulate<1|2>:LIMit<1...8>:CLEar[:IMMediate]
COPY
LIMIT LINE
:CALCulate<1|2>:LIMit<1...8>:COPY 1...8 | <name>
DELETE
LIMIT LINE
:CALCulate<1|2>:LIMit<1...8>:DELete
X OFFSET
:CALCulate<1|2>:LIMit<1...8>:CONTrol:OFFset <num_value>
Y OFFSET
:CALCulate<1|2>:LIMit<1...8>:UPPer:OFFset <num_value>
:CALCulate<1|2>:LIMit<1...8>:LOWer:OFFset <num_value>