13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged
in any way, such as when the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14. Do not expose this apparatus to dripping or splashing,
and ensure that no objects filled with liquids, such as vases,
are placed on the apparatus.
15. To completely disconnect this apparatus from the AC
Mains, disconnect the power supply cord plug from the AC
receptacle.
16. The mains plug of the power supply cord shall remain
readily operable.
17. Indoor Use: WARNING: To reduce the risk of fire or
electric shock, do not expose this apparatus to rain or
moisture.
18. The safe operation of this product requires that a
protective earth connection be provided. A grounding
conductor in the equipment's supply cord provides this
protective earth. To reduce the risk of electrical shock to the
operator and service personnel, this ground conductor must
be connected to an earthed ground.
19. WARNING: This apparatus, when equipped with multiple
power supplies, can generate high leakage currents. To
reduce the risk of electric shock, ensure that each individual
supply cord is connected to its own separate branch circuit
with an earth connection.
20. CAUTION: These service instructions are for use by
qualified service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that contained
in the operating instructions unless you are qualified to do
so.
21. Service barriers within this product are intended to protect
the operator and service personnel from hazardous voltages.
For continued safety, replace all barriers after servicing.
22. Certain parts of this equipment still present a safety
hazard with the power switch in the OFF position. To avoid
electrical shock, disconnect all A/C power cords from the
chassis' rear appliance connectors before servicing.
23. This product contains safety critical parts, which, if
incorrectly replaced, may present a risk of fire or electrical
shock. Components contained within the product's power
supplies and power supply area are not intended to be
customer-serviced and should be returned to the factory for
repair.
24. To reduce the risk of fire, replacement fuses must be the
same type and rating.
25. Use only power cords specified for this product and
certified for the country of use.
26. The safe operation of this equipment requires that the
user heed and adhere to all installation and servicing
instruction contained within the equipment's Engineering
Manuals.
27. WARNING: This product includes an “Ethernet Port”
which allows this product to be connected to a local area
network (LAN). Only connect to networks that remain inside
the building. Do not connect to networks that go outside the
building.
EMC Notices
United States of America — FCC Part 15
This equipment has been tested and found to comply
with the limits for a class A Digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
Important: Changes or modifications to this
equipment not expressly approved by Ross Video
Limited could void the user's authority to operate this
equipment.
Canada
This Class “A” digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe “A” est conforme a
la norme NMB-003 du Canada.
Europe
This equipment is in compliance with the essential
requirements and other relevant provisions of CE
Directive 93/68/EEC.
International
This equipment has been tested to CISPR 22:1997 along
with amendments A1:2000 and A2:2002, and found to
comply with the limits for a Class A Digital device.
Important: This is a Class A product. In domestic
environments, this product may cause radio
interference, in which case the user may have to
take adequate measures.
General Handling Guidelines
• Careful handling, using proper ESD precautions,
must be observed.
• Power down the system before PCB removal.
A Word About Static Discharge
Throughout the many procedures in this manual, please
observe all static discharge precautions.
Caution: Avoid handling the switcher circuit boards
in high static environments such as carpeted areas,
and when synthetic fiber clothing is worn. Touch the
4 • Document Information — Carbonite Setup Manual (v10.0)
To Next Page
Loading...
Need help?
General
