Home
RYTEC
Controller
System 3
RYTEC System 3 User Manual
5
of 1
of 1 rating
42 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
32
SYSTEM STARTUP—FAULT CODES
F.
9
6
3
Incorrect ramp parameters
1. Control system not initialized
with ne
w
EPROM
1. check pa
rameters
, cycle po
wer
, consult
fac
to
r
y
F.
9
6
4
Program v
ersion
1. Control system not initialized
with ne
w
EPROM
1. cycle po
wer
, consult f
actor
y
F.
9
7
0
Incorrect parameter
.
1. parameters inco
rrectly set
Check parameters
, cycle pow
er
, consult
fac
to
r
y
Fau
l
t
C
o
d
e
(Contr
ol System)
Description
Corrective Action
37
39
Table of Contents
Default Chapter
3
Table of Contents
3
Introduction
7
How to Use Manual
7
Required Tools and Equipment
7
Additional Requirements
7
Labor and Site Requirements
7
Electrician's Responsibilities
7
Shipping Crate
7
System Overview
8
Control Panel
8
Controller
9
Two-Line Display
9
Status Leds
9
Plug-In Modules
9
Installation
10
Wall Anchors
10
Control Panel Installation
10
System Inputs
12
Power Supply Lines
12
Motor
12
Motor Brake
12
Encoder
12
External Emergency Stop Switches (N.C. Contacts)
12
E-Stop 1
12
E-Stop 2
12
Breakaway Bottom Bar (Input 1 - N.C. Contact)
12
Photo Eye - Front (Input 2 - N.C. Contact)
13
Photo Eye - Back (Input 3 - N.C. Contact)
13
Alternate-Action Activator (Input 4 - N.O. Contact)
13
Auto-Close Activator 1 (Input 5 - N.O. Contact)
13
Auto-Close Activator 2 (Inputs 6 and 7 - N.O. Contact)
13
Open (Input 8 - N.O. Contact)
13
Close (Input 9 - N.O. Contact)
13
Stop (Input 10 - N.C. Contact)
13
Programmable (Inputs 11 and 12 - N.O. or N.C. Contact)
14
DC Power Supply - Photo Eyes
14
DC Power Supply - Auxiliary Device
14
Reversing Edge
14
Timers
14
System Startup
14
Modes of Operation
14
Run Mode
14
Automatic Mode
14
Non-Automatic Mode
15
Parameter Mode
15
System Controls
15
Service Levels
15
Initial Start-Up
16
Accessing Parameters
16
Parameter Messages
16
Navigating Parameters
17
Accessing Service Levels 1 and 2
17
Setting Door Limits (Open, Intermediate, and Close)
18
Fine Tuning Limit Settings
18
Close Limit Adjustment
18
Open Limit Adjustment
19
Setting Automatic Delay Timers
19
Accessing Error Log
19
Defrost System
20
Parameters
21
Operator Level Parameters
21
Service Level 1 Parameters
22
Service Level 2 Parameters
24
Fault Codes
32
General Operation Fault Codes
32
Door Safety/Emergency System Fault Codes
33
Reversing Edge Circuit Fault Codes
33
Drive System Fault Codes (400-Level Codes)
34
Drive System Fault Codes (500-Level Codes)
35
Door Position Fault Codes
36
Control System Fault Codes
37
Specifications
39
Mechanical
39
Inputs
39
Outputs
40
Optional Plug-In Modules
41
Optional 24-Vac Transformer (Standard Control Panel Only)
41
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the RYTEC System 3 and is the answer not in the manual?
Ask a question
RYTEC System 3 Specifications
General
Brand
RYTEC
Model
System 3
Category
Controller
Language
English
Related product manuals
RYTEC System 4
72 pages
RYTEC DG1200
26 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
