What to do if my SAJ Inverter shows a GFCI Error M?
If a GFCI Error M occurs with your SAJ Inverter, it indicates a ground fault on either the DC or AC side. Check the insulation of the modules and external surge protection. Also, examine the ambient conditions, as humidity can increase the likelihood of this error. Verify the internal ground connection. If the error persists after these checks, further assistance is needed.
What causes L1 No Grid Err M on my SAJ Suntrio-TL Inverter and how can I fix it?
If your SAJ Inverter displays an L1 No Grid Err M, it means there might be connection problems between the grid and the inverter, or the connection is missing. Check the AC connection. If the connection is correct, further assistance is needed.
How to troubleshoot Fan1 Error M on a SAJ Suntrio-TL?
If a Fan1 Error M occurs on your SAJ Inverter, the fan may be locked or damaged. Check the fans under the inverter's case. If the fans appear to be in good condition, clean them. If the error continues, further assistance is needed.
What does HWBus Volt High M mean on my SAJ Suntrio-TL?
If your SAJ Inverter shows a HWBus Volt High M error, it indicates that the voltage of the PV string connected to the inverter is higher than the hardware limited value, or there's a sudden DC surge. Check the PV string configuration, using the SAJ Designer for assistance. If the configuration is correct, further assistance is needed.
Why does my SAJ Inverter show a Temp. High Err M?
A Temp. High Err M on your SAJ Inverter can be due to a defective thermal resistance or an environment temperature that is too high or too low. If the thermal resistance is defective, replace it. Check the ambient and installation conditions. If the issue persists, further assistance is needed.
What does L1 Voltage High M mean on my SAJ Suntrio-TL Inverter?
An L1 Voltage High M error on your SAJ Inverter can occur if the local grid voltage is beyond the permitted range or if there are connection problems between the grid and the inverter. Check the Grid Compliance of the inverter and Grid voltage. If everything appears correct, further assistance is needed.
Why is my SAJ Suntrio-TL Inverter showing L1 Freq High M?
An L1 Freq High M error on your SAJ Inverter means that the local grid frequency is beyond the permitted range or there is a problem with the connection between the grid and the inverter. Check the Grid Compliance of the inverter and Grid frequency. If everything is correct, further assistance is needed.
What causes a PV1 Volt High S error on my SAJ Suntrio-TL Inverter?
A PV1 Volt High S error on your SAJ Inverter can be caused by the open-circuit voltage of the PV generator being higher than the maximum DC input voltage of the inverter, or a sudden DC surge. Check the PV string configuration, using the SAJ Designer for assistance. If the configuration is correct, further assistance is needed.
What should I do if my SAJ Suntrio-TL Inverter shows L1 No Grid Err S?
If your SAJ Inverter displays an L1 No Grid Err S, it indicates connection problems between the grid and the inverter, or a missing connection. Check the AC connection. If the connection is correct, further assistance is needed.
Why am I getting a PV Voltage Low S error on my SAJ Inverter?
If your SAJ Inverter displays a PV Voltage Low S error, it means the voltage of the PV input is too low. Check the PV string configuration, using the SAJ Designer for assistance. If the configuration is correct, further assistance is needed.
Defines the proper application of the inverter for converting DC to AC and feeding into the electricity grid.
Lists critical safety measures and warnings to prevent electrical shock and hazards during operation and maintenance.
Details the correct procedures and considerations for physically mounting the inverter, including orientation and clearance.
Provides step-by-step instructions for attaching the inverter to the wall using the provided mounting hardware.
Emphasizes critical safety precautions related to electrical discharge and grounding before connecting components.
Recommends specific circuit breaker specifications for safe DC and AC disconnection of the inverter.
Outlines the conditions and requirements for safely connecting the inverter to the public electricity grid.
Describes the procedures and conditions for connecting the solar photovoltaic array to the inverter's DC inputs.
Provides a detailed, step-by-step guide for connecting DC cables using H4 connectors, including stripping and crimping.
Explains how error reports are generated and displayed, guiding users to relevant troubleshooting information.
General| Protection degree | IP65 |
|---|---|
| Output Frequency | 50 Hz / 60 Hz |
| Protection Level | IP65 |
| Model | Suntrio-TL Series |
| MPPT Voltage Range | 200V - 1000V |
| Number of MPPTs | 2 |
| Cooling | Smart Fan Cooling |
| Number of MPP Trackers | 2 |
| Operating Temperature Range | -25 °C ~ +60 °C |
| Storage Temperature Range | -40 °C ~ +70 °C |
| Humidity Range | 0 - 100% |
| Communication | RS485, Wi-Fi, GPRS |
To Next Page